Instruction Manual

AD-4406 Weighing Indicator Page 45
13.2.
13.2.13.2.
13.2. Data
Data Data
Data Format
FormatFormat
Format
There are two types of data format set at F-Function F34 and F35.
The initial data format of F34 is shown below.
Header 1 F34, 35 : 9 (Status)
ST Stable weight data.
US Unstable weight data.
OL Overload (Out of range).
HD Hold weight data (The response of the “RW” and “RW,n” command).
Header 2 F34, 35 : E (Weight type)
GS or G Gross data.
NT or N Net data
TR or T Tare data.
Data F34, 35 : A, B, C, D (Weight data)
The first of the data bits is the polarity, "+" or "-".
When data is zero, the polarity is "+".
8 digits (bits) including the polarity and a decimal point (dot or comma).
In case of "Out of range", the data bits are replaced by spaces except for the decimal
point.
Unit F34, 35 : F (Unit)
In case of CF07=0, the unit length is 2 digits.
In case of CF07=1, the unit length is 3 digits. Depending on the circumstances, an
A&D printer may not work correctly.
13.3.
13.3.13.3.
13.3. Command Format
Command FormatCommand Format
Command Format
Description of Command
When performing a command, the received command or reply data is sent back.
When the received command can not be performed such as the "busy" state, the
code " I " is sent back. In this case, insert a delay time. Electrical noise may be the
cause of this error.
13.2. Data Format
㪚㪸㫉㫉㫀㪸㪾㪼㩷㫉㪼㫋㫌㫉㫅㩷㩿㪇㪛㪿㪀
㪚㪸㫉㫉㫀㪸㪾㪼㩷㫉㪼㫋㫌㫉㫅㩷㩿㪇㪛㪿㪀㪚㪸㫉㫉㫀㪸㪾㪼㩷㫉㪼㫋㫌㫉㫅㩷㩿㪇㪛㪿㪀
㪚㪸㫉㫉㫀㪸㪾㪼㩷㫉㪼㫋㫌㫉㫅㩷㩿㪇㪛㪿㪀
㪚㪝㪇㪍㪔㪇㪃㪈㩷 㩷 㪚㪝㪇㪍㪔㪉 㪚㪝㪇㪎㪔㪇㩷㩷㩷㪚㪝㪇㪎㪔㪈
㪉㩷㪻㫀㪾㫀㫋㫊㩷㩷㪊㩷㪻㫀㪾㫀㫋㫊
Header 1 Header 2
Unit
8-digit data
Terminator
T
S
, S
G
+
,
0
0
0
0
0 0
.
g
k
T
S
S
U
L
O
D
H
G
N
T
S
G
T
N
R
T
g
t
g
k
g
t
g
k
l
t
b
l
l
t
b
l
zo
y
c
zo
yc
㪪㫇㪸㪺㪼㩷㪺㫆㪻㪼㩷㩿㪉㪇㪿㪀
㪪㫇㪸㪺㪼㩷㪺㫆㪻㪼㩷㩿㪉㪇㪿㪀㪪㫇㪸㪺㪼㩷㪺㫆㪻㪼㩷㩿㪉㪇㪿㪀
㪪㫇㪸㪺㪼㩷㪺㫆㪻㪼㩷㩿㪉㪇㪿㪀
㪣㫀㫅㪼㩷㪽㪼㪼㪻㩷㩿㪇㪘㪿㪀
㪣㫀㫅㪼㩷㪽㪼㪼㪻㩷㩿㪇㪘㪿㪀㪣㫀㫅㪼㩷㪽㪼㪼㪻㩷㩿㪇㪘㪿㪀
㪣㫀㫅㪼㩷㪽㪼㪼㪻㩷㩿㪇㪘㪿㪀
㪛㪼㪺㫀㫄㪸㫃㩷㫇㫆㫀㫅㫋㩷㪑
㪛㪼㪺㫀㫄㪸㫃㩷㫇㫆㫀㫅㫋㩷㪑㪛㪼㪺㫀㫄㪸㫃㩷㫇㫆㫀㫅㫋㩷㪑
㪛㪼㪺㫀㫄㪸㫃㩷㫇㫆㫀㫅㫋㩷㪑
㩷 㪛㫆㫋㩷㩿㪉㪜㪿㪀㩷㫆㫉
㩷 㪛㫆㫋㩷㩿㪉㪜㪿㪀㩷㫆㫉㩷 㪛㫆㫋㩷㩿㪉㪜㪿㪀㩷㫆㫉
㩷 㪛㫆㫋㩷㩿㪉㪜㪿㪀㩷㫆㫉
㩷 㪚㫆㫄㫄㪸㩷㩿㪉㪚㪿㪀
㩷 㪚㫆㫄㫄㪸㩷㩿㪉㪚㪿㪀㩷 㪚㫆㫄㫄㪸㩷㩿㪉㪚㪿㪀
㩷 㪚㫆㫄㫄㪸㩷㩿㪉㪚㪿㪀