User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
PCM-3347 User’s Manual 64
Chapter 7 PCI Bus Ethernet Interface
7.1 Introduction
The PCM-3347F/PCM-3348F is equipped with a high performance 32-
bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps
CSMA/CD standards. It is supported by major network operating sys-
tems. It is also both 100Base-T and 10Base-T compatible. The medium
type can be configured via the RSET8139.exe program included on the
utility disk.
The Ethernet port provides a 10-pin 2 mm connector on board.
7.2 Installation of Ethernet driver
Before installing the Ethernet driver, note the procedures below. You
must know which operating system you are using in your PCM-3347F/
PCM-3348F, and then refer to the corresponding installation flow chart.
Then just follow the steps described in the flow chart. You will quickly
and successfully complete the installation, even if you are not familiar
with instructions for MS-DOS or Windows.
7.2.1 Installation for MS-DOS and Windows 3.1
If you want to set up your Ethernet connection under the MS-DOS or
Windows 3.1 environment, you should first check your server system
model. For example, MS-NT, IBM-LAN server, and so on. Then choose
the correct driver to install in your panel PC.
The installation procedures for various servers can be found on CD-
ROM. The file path is: D:\LAN\8100BL\
Note: The windows illustrations in this chapter are
examples only. You must follow the flow chart
instructions and pay attention to the instructions
which then appear on your screen.