User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
PCM-3347 User’s Manual 20
Chapter 3 Software Configuration
3.1 Introduction
The PCM-3347 system BIOS and custom drivers are located in a 256 KB,
32-pin (JEDEC spec.) Flash ROM device, designated U18. A single Flash
chip holds the system BIOS and VGA BIOS. The display can be config-
ured via CMOS settings. This method minimizes the number of chips and
difficulty of configuration. To set different types of LCD panels, please
choose ìpanel typeî from the ìintegrated peripheralsî menu in CMOS
setup.
3.2 Connections for four standard LCDs (PCM-3347)
3.2.1 Sharp LM64183P,LM64P89 (640x480 DSTN MONO LCD)
Warning! Do not remove the plastic rear cover until you
have verified that no power is flowing within the
panel PC. Power must be switched off and the
power cord must be unplugged. Every time you
service the panel PC, you should be aware of
this.
Table 3.1: Sharp LM64183P & LM64P89
LM64183/64P89 PCM-3347 CN7
Pin Name Pin Name
CN1-1 S 36 FLM
CN1-2 CP1 38 LP
CN1-3 CP2 35 SHFCLK
CN1-4 DISP 1 +5 V
CN1-5 VDD 2 +5 V
CN1-6 VSS 3 GND
CN1-7 VEE - External power*
CN1-8 DU0 12 P3
CN1-9 DU1 11 P2
CN1-10 DU2 10 P1