User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
17 Chapter 2
If your cable needs to be custom made, you can find the pin assignments
for the board's connector in Appendix C.
2.17 LCD-B connector (CN11)
The PCM-3347F supports 36-bit LCD that must be connected to both
CN7 (40-pin) and CN11 (20-pin).
The pin assignments for both CN7 and CN11 can be found in Appendix
C.
2.18 CompactFlash™ socket (CN22)
The PCM-3347 is equipped with a CompactFlash™ disk socket on the
solder side, which supports the IDE interface CompactFlash disk card.
The socket itself is specially designed to prevent any incorrect installation
of the CompactFlash disk card. When installing or removing the Com-
pactFlash disk card, please make sure that the system power is off.
The CompactFlashô disk card is defaulted as the E disk drive in your PC
system. To fit the Advantech CFC into the PCM-3347, simply plug it into
the designated connector. It will only fit when the red triangle on the CFC
is aligned with the triangle on the connector. The card will not fit any
other way (do NOT use excessive force).
2.19 I2C BUS (CN4)
PCM-3347 provides a 2-pin I2C connector.
2.20 HDD LED connector (CN15)
PCM-3347 provides a 2-pin LED connector.