User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
15 Chapter 2
2.11.1 CRT display connector (CN10)
CN10 is a 16-pin, pin head housing connector. Please use the
VGA cable (provided with your kit) to convert the pin head
housing connector into a connector for conventional CRT
displays.
Detailed information on pin assignments for CRT display
connector CN10 is given in Appendix C.
2.12 Reset button connector (CN13)
If you install a reset button, it should be a single pole switch
rated at 5 V. Momentarily pressing the button will activate a
reset. For reset button pin assignments, please see Appendix
C.
2.13 Main power (+5 V / +12 V) connector (CN14)
This supplies main power to the PCM-3347 (+5 V), and also 12 V power
to the backlight connector.
2.14 PS/2 Keyboard/mouse connector (CN18)
The PCM-3347 board provides a pin head keyboard connector, which
supports both a keyboard and a PS/2 style mouse. In most cases, espe-
cially in embedded applications, a keyboard is not used. If the keyboard is
not present, the standard PC/AT BIOS will report an error or failure dur-
ing the power-on self test (POST) after resetting the PC. The PCM-3347
board's BIOS standard setup menu allows you to select "Absent/Present"
for your keyboard under the Advanced CMOS Setup section. This allows
non-keyboard operation in embedded system applications without the
system halting during the POST. When "PS/2 mouse support" is enabled,
your PS/2 mouse is automatically detected by the system.