User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
PCM-3347 User’s Manual 14
1. Connect one end of the cable to CN1. Make sure that the red (or
blue) wire corresponds to pin 1 on the connector, which is labeled on the
board (on the right side).
2. Plug the other end of the cable into the Enhanced IDE hard drive,
with pin 1 on the cable corresponding to pin 1 on the hard drive. Unlike
floppy drives, IDE hard drives can connect to either end of the cable. If
you install two drives, you will need to set one as the master and one as
the slave by using jumpers on the drives. If you install just one drive, set
it as the master.
2.8 PC/104 connector (CN17, CN19)
Refer to Appendix B in this manual.
2.9 Parallel port connector (CN12)
Normally, the parallel port is used to connect the card to a
printer. The PCM-3347 includes a multi-mode (ECP/EPP/
SPP) parallel port. It is accessed via CN12, a 26-pin flat-
cable connector.
You will need an adapter cable if you use a traditional DB-25
connector. The adpater cable should have a 26-pin connector
on one end and a DB-25 connector on the other.
The parallel port interrupt channel is designated as IRQ7.
2.10 Backlight connector (CN3) PCM-3347
The LCD inverter is connected to CN3 via a 4-pin connector
to provide +12 V power to the LCD display.
2.11 VGA connector (CN10)
The PCM-3347 board's SVGA interface can facilitate con-
ventional CRT displays. The card has a connector to support
CRT VGA monitors.