User`s manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Introduction
- 2.1 Connectors (PCM-3348 has no LCD connectors)
- 2.2 Locating connectors
- 2.3 Installation Procedures
- 2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
- 2.5 LCD-A display connector (CN7)
- 2.6 Serial ports (CN5, CN6, CN8, CN9)
- 2.7 EIDE HDD connector (CN1)
- 2.8 PC/104 connector (CN17, CN19)
- 2.9 Parallel port connector (CN12)
- 2.10 Backlight connector (CN3) PCM-3347
- 2.11 VGA connector (CN10)
- 2.12 Reset button connector (CN13)
- 2.13 Main power (+5 V / +12 V) connector (CN14)
- 2.14 PS/2 Keyboard/mouse connector (CN18)
- 2.15 5 V connector (CN16)
- 2.16 FDD connector (CN22)
- 2.17 LCD-B connector (CN11)
- 2.18 CompactFlash™ socket (CN22)
- 2.19 I2C BUS (CN4)
- 2.20 HDD LED connector (CN15)
- 2.21 SIR connector (CN20)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- Chapter 5 SVGA Setup
- Chapter 6 PCI SVGA Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104 Modules
- Appendix C Pin Assignments
- C.1 Ethernet connector (CN2)
- C.2 LCD-A connector (CN7)
- C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8)
- C.4 COM2 connector (CN5, CN23)
- C.5 EIDE hard drive connector (CN1)
- C.6 PC/104 connector (CN17, CN19)
- C.7 Parallel port connector (CN12)
- C.8 Backlight connector (CN3)
- C.9 VGA connector (CN10)
- C.10 Reset button connector (CN13)
- C.11 Main power (+5 V) connector (CN14)
- C.12 PS/2 keyboard/mouse connector (CN18)
- C.13 5 V connector (CN16)
- C.14 FDD connector (CN22)
- C.15 LCD-B connector (CN11)
- C.16 CompactFlash™ socket (CN21)
- Appendix D System Assignments
- Appendix E LCD Services
PCM-3347 User’s Manual 12
2.3 Installation Procedures
2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
The PCM-3347F is equipped with a high performance 32-bit PCI-bus
Fast Ethernet interface which is fully compliant with IEEE 802.3u 100/
10Base-T specifications. It is supported by all major network operating
systems.
The medium type can be configured via the RSet8139.EXE program
included on the utility disk. (See Chapter 5 for detailed information.)
2.4.1 Ethernet connector (CN2)
10/100Base-T connects to the PCM-3347F and PCM-3348 via an adapter
cable to the 10-pin 2 mm connector.
2.5 LCD-A display connector (CN7)
CN7 is a 40-pin dual-in-line header and is used to connect an LCD dis-
play to the PCM-3347F.
Warning: Always completely disconnect the power cord
from your board whenever you are working on it.
Do not make connections while the power is on,
because sensitive electronic components can be
damaged by a sudden rush of power.
Caution: Always ground yourself to remove any static
charge before touching the board. Modern elec-
tronic devices are very sensitive to static electric
charges. Use a grounding wrist strap at all times.
Place all electronic components on a static-dissi-
pative surface or in a static-shielded bag when
they are not in the chassis.