Installation Guide

Ceiling Mounted Detection Sensor
RTCGE01
Datasheet
General Specifications
Features
Dimensions
Weight (with battery)
Casing
94mm in diameter,
38mm in thickness
83.5g
ABS plastic
Environment Requirements
Operating temperature
Operating humidity
Mounting location
Mounting
Detection angle
Detection distance
-10～45℃
0～95%RH, no condensation
3m away from the floor
Srews / Adhesives
360°
≤7m
Power
Battery
Battery life
AAA battery x 2
5 years
Others
IP rating
Standards
IP52
EN 60669-1
EN 60669-2-1
Dynamic Human Body Detection
*
RTCGE01 Ceiling Mounted Detection Sensor adopts the
third generation of passive infrared sensors (PIR) detec-
tion technology. With built-in high-precision algorithm
unit, RTCGE01 can automatically adapt to specific room
environments and filter out interference caused by
temperature and humidity changes.
The sensor can
effectively identify people up to a range of 7 meters.
Powered by two easily replaceable AAA batteries, giving
the sensor a life span of over 5 years. RTCGE01 is fixed
in a central location of a room using an adhesive, with an
installation time of <1 minute.
When a person moves within the detection range of the RTCGE01,
the sensor can respond almost instantaneously and report the
status change.
Bluetooth Mesh Technology
Bluetooth Mesh technology used in RTCGE01 is a global wireless
standard for communication between smart devices in industrial
automation environments. Bluetooth Mesh technology uses a
reliable mesh network to keep devices connecte
d and working
together while providing excellent battery life.
Dynamic Temperature Compensation
Dynamic temperature compensation enables RTCGE01 to
automatically monitor the ambient temperature and adjust the
signal processing algorithms to maintain normal sensing perfor-
mance in varying temperatures.
Real-time Data Reporting and Offline Caching
RTCGE01 reports measurement data through the gateway with a
delay of less than 100 ms. If the sensor is offline, the data will be
cached locally and transmitted after the network connection is
restored.
The above data is measured by 9am laboratory, and may be
affected by environmental factors.
• www.9amtech.com
• contact
@9amtech.com
• 400-037-8109
Installation Guide
*
The recommended installation height is between 2m and 3m. Installed
below 2m or above 3m, blind spots will appear and some area cannot be
detected.
2-3m
0m 2m2m 4.5m4.5m 7m7m
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed
and operated with minimum distance 20cm between the radiator & body.