User's Manual
Table Of Contents
- 1. Getting started
- 2. Introduction
- 3. Preparation
- 4. About the terminal
- 5. Mounting and installing the terminal
- 6. Connecting to the terminal
- 7. Managing the terminal
- 8. Configuring the terminal
- 9. Configuring the traffic interfaces
- 10. Cross Connections
- Embedded cross connect switch
- The Cross Connections application
- The Cross Connections system requirements
- Installing the Cross Connections application
- Opening the Cross Connections application
- The Cross Connections page
- Setting the terminal's address
- Management and user ethernet capacity
- Setting card types
- Getting cross connection configuration from the terminals
- Creating cross connections
- Sending cross connection configuration to the terminals
- Saving cross connection configurations
- Using existing cross connection configurations
- Printing the cross connection configuration
- Deleting cross connections
- Configuring the traffic cross connections
- Cross connection example
- Symmetrical Connection Wizard
- 11. Protected terminals
- 12. In-service commissioning
- What you will need
- Checking the antenna polarization
- Visually aligning antennas
- Accurately aligning the antennas
- Synchronizing the terminals
- Checking performance
- Checking the receive input level
- Checking the fade margin
- Checking long-term BER
- Bit Error Rate tests
- Additional tests
- Checking the link performance
- Viewing a summary of the link performance
- What you will need
- 13. Maintenance
- 14. Troubleshooting
- 15. Interface connections
- 16. Alarm types and sources
- 17. Country specific settings
- 18. Specifications
- Ethernet interface
- QJET Quad E1 / T1 interface
- Q4EM Quad 4 wire E&M interface
- DFXO Dual foreign exchange office interface
- DFXS Dual foreign exchange subscriber interface
- QV24 Quad V.24 asynchronous data interface
- HSS Single high speed synchronous data interface
- External alarm interfaces
- Auxiliary interfaces
- AC Power supply
- DC Power supply
- Power consumption
- MHSB protection
- Ethernet interface
- 19. Product end of life
- 20. Abbreviations
- 21. Acknowledgments and licensing
- 22. Commissioning Forms
- 23. Index
Specifications | 238
System performance specifications
Capacity ETSI
C2
Channel size
25 kHz
C3
Gros s 72 kbit/s 96 kbit/s 112 kbit/s
E1 1 timeslots 1 timeslots 1 timeslots
Ways ide 8 kbit/s 32 kbit/s 48 kbit/s
50 kHz
C3
Gros s 80 kbit/s 168 kbit/s 208 kbit/s 256 kbit/s
E1 1 timeslots 2 timeslots 3 timeslots 4 timeslots
Ways ide 16 kbit/s 40 kbit/s 16 kbit/s 0 kbit/s
75 kHz
C4
Gros s 128 kbit/s 264 kbit/s 312 kbit/s 400 kbit/s
E1 2 timeslots 4 timeslots 4 timeslots 6 timeslots
Ways ide 0 kbit/s 8 kbit/s 56 kbit/s 16 kbit/s
150 kHz
C4
Gros s 264 kbit/s 536 kbit/s 672 kbit/s 808 kbit/s
E1 4 timeslots 8 timeslots 10 timeslots 12 timeslots
Ways ide 8 kbit/s 24 kbit/s 32 kbit/s 40 kbit/s
200 kHz
C5
Gros s 336 kbit/s 680 kbit/s 840 kbit/s
E1 5 timeslots 10 timeslots 13 timeslots
Ways ide 16 kbit/s 40 kbit/s 8 kbit/s
250 kHz Gross 408 kbit/s 824 kbit/s 1032 kbit/s 1240 kbit/s
E1 6 tim es lots 12 tim es lots 16 tim es lots 19 tim es lots
Ways ide 24 kbit/s 56 kbit/s 8 kbit/s 24 kbit/s
500 kHz Gross 792 kbit/s 1592 kbit/s 1992 kbit/s 2392 kbit/s
E1 12 tim es lots 24 tim es lots 31 tim eslots 1 E1
Ways ide 24 kbit/s 56 kbit/s 8 kbit/s 304 kbit/s
1 MHz Gros s 1624 kbit/s 3256 kbit/s 4072 kbit/s 4888 kbit/s
E1 25 timeslots 1 E1 1 E1 2 E1
Ways ide 24 kbit/s 1168 kbit/s 1984 kbit/s 712 kbit/s
1.75 MHz Gros s 2872 kbit/s 5752 kbit/s 7192 kbit/s 8632 kbit/s
E1 1 E1 2 E1 3 E1 4 E1
Ways ide 784 kbit/s 1576 kbit/s 928 kbit/s 280 kbit/s
3.5 MHz Gross 5720 kbit/s 11448 kbit/s 14312 kbit/s 17176 kbit/s
E1 2 E1 5 E1 6 E1 8 E1
Wayside 1544 kbit/s 1008 kbit/s 1784 kbit/s 472 kbit/s
7 MHz
C6
Gross 11832 kbit/s 23672 kbit/s 29592 kbit/s 35512 kbit/s
E1 5E1 11E1 14E1 17E1
Ways ide 1392 kbit/s 704 kbit/s 360 kbit/s 16 kbit/s
14 MHz
C6
Gross 23992 kbit/s 47992 kbit/s 59992 kbit/s 65464 kbit/s
E1 11 E1 22 E1 28 E1 28 E1
Ways ide 1024 kbit/s 2056 kbit/s 1528 kbit/s 7000 kbit/s
Note C2 The capacities specified are for Unframed E1 and so require 2088 kbit/s to transport via the radio.
The management ethernet capacity must be subtracted from the gross capacity (default 64 kbit/s).
Note C3 Available only in the 300 and 400 MHz bands.
Note C4 Available only in the 300, 400 and 1400 MHz bands.
Note C5 Available only in the 700, 800 and 900 MHz bands.
Note C6 Available only in the 2000 and 2500 MHz bands.
64 QAMQPSK 16 QAM 32 QAM