Datasheet
4D SYSTEMS uLCD-35DT Display Module
© 2014 4D SYSTEMS Page 11 of 24 www.4dsystems.com.au
uLCD-35DT Display Module
DIABLO16 Alternate Pin Configurations
SPI Communications
SPI1 SDO
SPI1 SDI
SPI1 SCK
SPI2 SDO
SPI2 SDI
SPI2 SCK
SPI3 SDO
SPI3 SDI
SPI3 SCK
PA0
✓
✓
✓
PA1
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA2
✓
✓
✓
PA3
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA4
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA5
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA6
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA7
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA8
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA9
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA10
✓
✓
✓
PA11
✓
✓
✓
PA12
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA13
✓
✓
✓
✓
✓
✓
✓
✓
✓
PA14
PA15
The following table illustrates which of the GPIO
can be used for the three different I
2
C channels
available.
DIABLO16 Alternate Pin Configurations
I
2
C Communications
I
2
C1 SDA
I
2
C1 SCL
I
2
C2 SDA
I
2
C2 SCL
I
2
C3 SDA
I
2
C3 SCL
PA0
✓
✓
✓
✓
✓
✓
PA1
✓
✓
✓
✓
✓
✓
PA2
✓
✓
✓
✓
✓
✓
PA3
✓
✓
✓
✓
✓
✓
PA4
✓
✓
✓
✓
✓
✓
PA5
✓
✓
✓
✓
✓
✓
PA6
✓
✓
✓
✓
✓
✓
PA7
✓
✓
✓
✓
✓
✓
PA8
✓
✓
✓
✓
✓
✓
PA9
✓
✓
✓
✓
✓
✓
PA10
✓
✓
✓
✓
✓
✓
PA11
✓
✓
✓
✓
✓
✓
PA12
✓
✓
✓
✓
✓
✓
PA13
✓
✓
✓
✓
✓
✓
PA14
SPECIAL
SPECIAL
SPECIAL
PA15
SPECIAL
SPECIAL
SPECIAL
SPECIAL – please see Section 4.7
SPI 4.6.
There are 3 user configurable SPI channels
available for mapping to GPIO, for use by the user
for the target application. All 3 SPI channels are
Master only, and cannot be configured to be
slaves at this time.
The SPI Bus speed is configurable using the
SPIx_Init() Function in 4DGL, and allows various
speeds from 78.125Khz to 17.5Mhz.
Please refer to the table on the previous page for
details on which GPIO can be configured for SPI.
Note: The additional SPI channel (SPI0) is
dedicated to memory cards and cannot be
reconfigured for alternate uses.
To map an SPI channel to a set of GPIO pins, the
following 4DGL functions are used:
SPIx_SCK_pin(pin); // Map the SCK pin
SPIx_SDI_pin(pin); // Map the SDI pin
SPIx_SDO_pin(pin); // Map the SDO pin
Where ‘SPIx’ is substituted with SPI1, SPI2 or SPI3
accordingly, and ‘pin’ is the target GPIO pin
compatible with that particular pin function.
Chip Select for use with SPI can be any other
unused GPIO pin, configured as a Digital Output.
The lowering and raising of the selected CS (GPIO)
pin is done manually by the user is the 4DGL
application.
Please refer to the separate document titled
'DIABLO16-4DGL-Internal-Functions.pdf' for more
information on how to use the SPI functions, along
with the separate document titled ‘DIABLO16-
Processor-Datasheet-REVx.x.pdf’.
I
2
C 4.7.
There are 3 user configurable I
2
C channels
available for mapping to GPIO, for use by the user
for the target application. All 3 I
2
C channels are
Master only, and cannot be configured to be
slaves at this time.
Please refer to the table on the previous page for
details on which GPIO can be configured for I
2
C.
To map an I
2
C Channel to a set of GPIO pins, the
following 4DGL function is used:
I2Cx_Open(Speed, SCLpin, SDApin);