Datasheet

ManualsBrands3M ManualsAdhesive Guns & AccessoriesMixing Nozzle for DP80x/810 50 ml

For footnotes, see Test Methods and Footnotes on Page 4.

Scotch-W

eld

Low-Odour Acrylic Adhesives

DP810

•

DP810 Black

•

DP810 NS

Product Description 3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives are two-part, 1:1 mix ratio,

toughened structural adhesives with less odour than most acrylic adhesives. These

adhesives have excellent shear and peel strength along with good impact resistance

and durability. They can quickly bond to most metals, ceramics, rubbers, plastics

and wood with minimal surface preparation.

Features • Tough, durable bonds • Low-odour acrylic adhesive

•

Minimal surface prep • 10 minute worklife

•

10 minute time to handling strength • 1:1 mix ratio

•

Bonds stainless steel • Excellent shear and peel strength

Typical Uncured

Physical Properties

Note: The following technical information and data should be considered representative

or typical only and should not be used for specification purposes.

Property

3M™ Scotch-Weld™ Low-Odour Acrylic Adhesive

DP810

DP810 Black

DP810 NS

Colour

Base (B)

Accelerator (A)

Green

White

Black

White

Blue/Green

White

Lbs./gal.

Base (B)

Accelerator (A)

8.7 - 9.1

Viscosity (cps)

(1)

Base (B)

Accelerator (A)

18,000 - 22,000

17,000 - 21,000

90,000 - 95,000

95,000 - 100,000

Base Resin

Base (B)

Accelerator (A)

Acrylic

Mix Ratio

(Volume)

(Weight)

1:1

Time to Handling Strength (50 psi)

10 minutes

Full Cure @ 23°C (73°F)

8 - 24 hours

Worklife @ 23°C (73°F)

10 minutes

Technical Data February, 2016

Summary of content (7 pages)

PAGE 1
TM Scotch-Weld Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Technical Data February, 2016 Product Description 3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives are two-part, 1:1 mix ratio, toughened structural adhesives with less odour than most acrylic adhesives. These adhesives have excellent shear and peel strength along with good impact resistance and durability. They can quickly bond to most metals, ceramics, rubbers, plastics and wood with minimal surface preparation.
PAGE 2
3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Typical Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
PAGE 3
M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Environmental Resistance(4) Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.
PAGE 4
3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Test Methods and Footnotes 1) Viscosity obtained by Brookfield, DV-II, #7 Spindle, 20 rpm at 24°C (75°F). 2) Overlap Shear Test Method: overlap shear test for adhesion determined in accordance to ASTM D1002-72, sample dimensions were 1" x 4" x 1/8", with a 1/2 square inch area of overlap, bonded to themselves unless otherwise noted, allowed to cure for at least 6 hours at 24°C (75°F) before testing.
PAGE 5
3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Handling/Curing Information Directions for use: Apply adhesive to clean, dry substrates, which are free of paint, oxide films, oils, dust, mold release agents and all other surface contaminants. See the Surface Preparation section for specific substrate preparation method. 50 ml cartridge:. Place Duo-Pak cartridge in 3M™ EPX Applicator. Remove cap. Dispense and discard a small amount of adhesive to assure even ratio and free flow.
PAGE 6
3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Surface Preparation 3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives can bond oily metal, plastic and other substrates with very little surface preparation. However, for the most consistent results and environmental resistance, all substrates should be clean, dry and free of paint, oxide films, dust, mold release agents and all other surface contaminants.
PAGE 7
3M™ Scotch-Weld™ Low-Odour Acrylic Adhesives DP810 • DP810 Black • DP810 NS Storage For maximum shelf life, store Duo-Pak cartridges and bulk containers at 0°C (32°F) to 4°C (40°F). Do not freeze. Shelf Life When stored at the recommended temperatures in the original unopened containers, this product has a shelf life of twelve months from date of shipment from 3M. Precautionary Information Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product.