User Guide

©2004, 3M. All rights reserved. 70-0709-5285-1
Specifications
GED Integrated Application System
Cycle time: <1 minute per unit
(24" x 36" 2 vertical x 1 horizontal lite)
Minimum
glass size: 12" x 12"
Maximum
glass size: 60" x 96" and up to 5/16" thick
Roll length: 120-yard roll of 3M
™
Accentrim
™
Product
GED Application Table
Cycle time: 3 minutes per unit (24" x 36"
2 vertical x 1 horizontal lite with square-cut ends)
Minimum
glass size: 8" x 8"
Maximum
glass size: 60" x 96" and up to 1/4" thick
Roll length: 60 or 120 yard roll of 3M
™
Accentrim
™
Product
Technical Data
Product Description
A linered optical film with a very clear, low out-gassing adhesive.
This product employs proprietary technology and has excellent
adhesion to glass surfaces, especially float glass. This permanent
adhesive resists edge lifting and discoloration, and has excellent
long-term aging properties.
Product No. Pattern
A-100 Edge Bevel
A-200 V-Groove
A-300 Fluted V-Groove
A-400 Half-Round with Center Transition
Construction
Description Material
Optical Layer Acrylic
Backing Polyester
Adhesive High strength acrylic
Release Liner Polyester with
release agent
Typical Physical Properties & Performance Characteristics
Note: The following technical information and data should be
considered representative or typical only and should not be used
for specification purposes.
Adhesion Float Glass
(ASTM D-3330) (oz./0.5in.[N/50mm])
Initial 40 (44)
After 3 days at 72°F (22°C) 60 (65)
General Information
• Not intended for outdoor application.
• Application temperature should be normal
room temperature, 60° to 80°F (16° to 27°C).
• Dimensionally stable over temperature range
from -20°F to 225°F (-29°C to 107°C).
• Reference 3M.com/accentrim for warranty information
regarding insulating glass.
TECHNICAL INFORMATION AND DATA: The technical information and data, recommendations, and other statements provided are based on tests or experience which 3M
believes to be reliable, but the accuracy or completeness of such information is not guaranteed.
PRODUCT USE: Please remember that many factors can affect the use and performance of a 3M product in a particular application. The materials to be adhered with the 3M
product, the surface preparation of those materials, the product selected for use, the conditions in which the product is used, and the time and environmental conditions in which
the product is expected to perform are among the many factors that can affect the use and performance of a 3M product. Given the variety of factors that can affect the use and
performance of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it
is fit for a particular purpose and suitable for the user's method of application.
3M MAKES NO OTHER WARRANTIES OR CONDITIONS, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. User is responsible
for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of application. If the 3M product is defective within the warranty period stated
above, YOUR EXCLUSIVE REMEDY AND 3M’S SOLE OBLIGATION SHALL BE, AT 3M’S OPTION, TO REPLACE OR REPAIR THE 3M PRODUCT OR REFUND THE
PURCHASE PRICE OF THE 3M PRODUCT. In no event shall 3M be liable for the labor or installation costs of replacing the 3M product.
Industrial Business
Industrial Adhesives and Tapes Division
Building 21-1W-10
900 Bush Avenue
St. Paul, MN 55144
1-800-362-3550
www.3M.com/accentrim