Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. 43 C º www.bairpaws.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Introduction to the 3M™ Bair Paws™ Patient Adjustable Warming System The 3MTM Bair PawsTM patient adjustable warming system consists of the Model 875 forcedair warming unit and disposable warming gowns. The Bair Paws Model 875 warming unit can provide comfort warming and prewarming to patients in preoperative settings.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Important Information about the Bair Paws Model 875 Warming Unit Indications The Model 875 warming unit is indicated for patient warming. This warming unit has been designed for use with the Bair Paws warming gowns in all preoperative and postoperative settings for pediatric and adult patients.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A No free hosing Date of manufacture Manufacturer This system is subject to European WEEE Directive 2002/96/EC. This product contains electrical and electronic components and must not be disposed of using standard refuse collection. Please consult local directives for disposal of electrical and electronic equipment.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A WARNING: 1. Do not use a forced-air warming device over transdermal medications; increased drug delivery, patient death, or injury may occur. 2.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A • Do not allow the power cord to get wet. • Remove the warming unit from service and contact 3M Patient Warming Technical Support at 1-800-773-7775 if the warming unit is subjected to a large fluid spill (e.g. I.V. or blood bag). • This equipment must only be connected to a supply mains with protective earth.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A NOTICE: 1. The Bair Paws warming unit meets the international electronic interference requirements. If radio frequency interference with monitoring equipment occurs, connect the warming unit to a different power source. 2. Federal law (USA) restricts this device to sale by or on the order of a licensed healthcare professional. 3.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Preparing the Bair Paws Model 875 Warming Unit for Use Before you begin using the warming unit, make sure that it is safely placed on a flat, hard surface such as a table, or securely mounted on a wall, IV pole, suction wall mount adapter, or bedrail.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Mounting the Warming Unit on an IV Pole CAUTION: To prevent tipping, mount the Model 875 warming unit on an IV pole at a height that ensures stability. We recommend mounting the warming unit no higher than 44 in. (112 cm) from the floor on an IV pole with a minimum wheelbase radius of 14 in. (35.6 cm).
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Mounting the Warming Unit on a Bedrail 1. If the warming unit is not already connected to the rail-mount, slide the clip on the back of the warming unit into the groove of the rail-mount. The assembly will click when the clip is fully seated in the rail-mount. 2. Hang the Model 875 warming unit on a bedrail by the hooks on the rail-mount. 3.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Mounting the Warming Unit with a Rail-mount to the Wall CAUTION: The rail-to-wall bracket is intended for use only with a Bair Paws 800 series warming unit. 1. If the warming unit is not already connected to the rail-mount, slide the clip on the back of the warming unit into the groove of the rail-mount.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Mounting the Warming Unit with a Suction Wall Mount Adapter 1. Slide the Bair Paws suction wall mount adapter into the suction wall bracket. If the adapter is too large to fit, remove the expand spacer. 2.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Operating Information Instructions for Use The instructions below describe how to use the Bair Paws Model 875 warming unit with a Bair Paws gown. For more information about the Bair Paws warming gowns, refer to the Instructions for Use that is shipped with the warming gowns. 1. Instruct your patient to put the warming gown on so the opening is in the back.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A 6. To disconnect the hose nozzle from the warming gown, press the two buttons on the sides of the nozzle and withdraw the nozzle from the hose port. 7. Store the warming unit hose by inserting it into the hose holder at top of unit. 8. Unplug the temperature management unit to disconnect the warming unit from power source.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Using the Handheld Temperature Controller After the hose has been connected to the Bair Paws gown, the patient can adjust the air temperature and airflow by turning the knob on the temperature controller. The following list explains how the unit will operate when the knob is placed in the specified position shown in the figure.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Using the Holder for the Handheld Temperature Controller Store the handheld temperature controller in the controller holder to help prevent cord clutter around the patient and accidental damage to the warming unit. 1. Press the holder onto the warming unit hose so it is within the patient’s reach.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A 5. Allow the warming unit to run for at least 5 minutes. • If the “Over-temp” light illuminates again, return the warming unit to 3M Patient Warming for service. • Otherwise, reconnect the warming unit hose to the Bair Paws gown to resume patient warming.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Technical Support and Customer Service U.S. Customer Service TEL: 800-228-3957 Outside of the USA Contact your local 3M Patient Warming representative. When You Call for Technical Support Please be ready to give the technical support representative the serial number of your Bair Paws warming unit. The serial number is located on the back of the unit.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Technical Specifications Physical Characteristics dimensions of warming unit 13 in. high x 4 in. deep x 7.7 in. wide 33 cm high x 10.2 cm deep x 19.6 cm wide dimensions of temperature controller 2.5 in. wide x 5.8 in. long 6.4 cm wide x 14.7 cm long relative noise level 57.9 dBA weight of warming unit 7.0 lb; 3.2 kg.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.com reorder #202391A Safety System Characteristics thermostat Independent electronic and heater (electromechanical) overcurrent protection Dual input fused line. safety feature Over-temperature protection: color indicator light illuminates, audible alarm sounds, and heater shuts down (blower continues to run). alarm system Fault: amber Fault indication flashes, alarm sounds.
Check the 3MTM Bair PawsTM system website to ensure you have the most recent version of this document. www.bairpaws.
Made in the USA of globally sourced material by 3M Health Care. 3M is a trademark of 3M Company, used under license in Canada. BAIR HUGGER, BAIR PAWS and the BAIR PAWS logo are trademarks of Arizant Healthcare Inc., used under license in Canada. ©2013 Arizant Healthcare Inc. All rights reserved. 3M Deutschland GmbH, Health Care Business Carl-Schurz-Str. 1, 41453 Neuss, Germany 3M Health Care, 2510 Conway Ave., St. Paul, MN 55144 USA TEL 800-228-3957 | www.bairpaws.