Cut Sheet

ManualsBrands3M ManualsConnectorsLoadbreak Elbow Connector

PHONE: 800-245-3573 www.3M.com/Electrical 309

Separable Connectors

200 Amp Load Break Elbows

Providing a convenient method to

connect/disconnect cable and equipment

on power distribution systems, loadbreak

elbows include provisions for energized

operation using standard hotstick tools,

allowing loadmake/break operation and a

visible disconnect. Components can be

isolated with insulated caps, plugs and

parking bushings.

The 3M™ 200 Amp Industrial Loadbreak

Elbow is a fully shielded and insulated

plug-in separable connector connecting 5-

25 kV. Designed to be used on tape shield,

wire shield, UniShield® and jacketed

concentric neutral types of cable. 3M's elbows are molded using high quality peroxide-cured EPDM

insulation and meet requirements of ANSI/IEEE Standard 386.

600 Amp Dead Break T-Bodies

600 Series deadbreak elbows are used to connect equipment and cable on primary feeder and network

circuits. The 3M™ Modular Splice Kit Series 5815 is easy to expand and is flexible – allowing for easy

disconnects and additions. With 3M modular technology, splices are designed to maintain the insulating

and shielding integrity of the original cable.

Easy to install, our modular splicing kits install easily on standard shielded power cables and are

compatible with copper and aluminum conductors. The 5815 Series kits are designed for use with tape

shield, wire shield, UniShield® and jacketed concentric neutral cables. Meets requirements of ANSI/IEEE

Standard 386.

Separable Connectors

IronwoodPremium_243240_Catalog-On-Demand9.QXD 7/11/2013 7:31 AM Page 309

Summary of content (20 pages)

PAGE 1
IronwoodPremium_243240_Catalog-On-Demand9.QXD 7/11/2013 7:31 AM Page 309 Separable Connectors Separable Connectors 200 Amp Load Break Elbows Providing a convenient method to connect/disconnect cable and equipment on power distribution systems, loadbreak elbows include provisions for energized operation using standard hotstick tools, allowing loadmake/break operation and a visible disconnect. Components can be isolated with insulated caps, plugs and parking bushings.
PAGE 2
IronwoodPremium_243240_Catalog-On-Demand9.QXD 7/11/2013 7:31 AM Page 310 Section Page 200 Amp Load Break Elbows ............................................................311-320 3M™ Industrial Loadbreak Elbow, 5810 Series (5-15 kV) .................................................311-315 3M™ Industrial Loadbreak Elbow, 5811 Series (25 kV).....................................................316-317 3M™ Cold Shrink 5110-0S Series 15–25/28 kV Cable Accessory Oil Stops .............................
PAGE 3
IronwoodPremium_243240_Catalog-On-Demand9.QXD 7/11/2013 7:31 AM Page 311 200 Amp Load Break Elbows 3M™ 200 Amp Industrial Loadbreak Elbow 5810 Series is a fully shielded and insulated plug-in separable connector for connecting 5–15 kV underground cable to transformers, switchgear and junctions equipped with loadbreak bushings. The elbow and the bushing insert comprise the essential components of all loadbreak connections.
PAGE 4
IronwoodPremium_243240_Catalog-On-Demand9.
PAGE 5
IronwoodPremium_243240_Catalog-On-Demand9.
PAGE 6
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 7
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 8
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:11 AM Page 316 200 Amp Load Break Elbows 3M™ Industrial Loadbreak Elbow, 5811 Series (25 kV) 3M™ 200 Amp Industrial Loadbreak Elbow 5811 Series is a fully shielded and insulated plug-in separable connector for connecting 25 kV underground cable to transformers, switchgear and junctions equipped with loadbreak bushings. The elbow and the bushing insert comprise the essential components of all loadbreak connections.
PAGE 9
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:11 AM Page 317 200 Amp Load Break Elbows Order No. UPC Insulation Diameter 5811-D-3/0 054007-43605 1.040"–1.250" (26,4–31,8 mm) 5811-D-4/0 054007-43606 1.040"–1.250" (26,4–31,8 mm) 5811-D-250 054007-43607 1.040"–1.
PAGE 10
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:11 AM Page 318 200 Amp Load Break Elbows: Accessories 3M™ Cold Shrink Cable Accessory Sealing Kits 8450 Series The 3M™ Cold Shrink Cable Accessory Sealing Kits 8450 Series are designed to seal the jacket end of power cables where elbows or other cable accessories are installed. Both the sealing tube and mastic are compatible with commonly used power cable jacketing and semiconductive materials.
PAGE 11
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:11 AM Page 319 200 Amp Load Break Elbows: Accessories The 3M™ Industrial Insulated Protective Cap is an accessory device designed to electrically insulate (dead-front) and mechanically seal loadbreak bushing interfaces. When mated to a loadbreak bushing interface with the drain wire attached to ground, the 3M Industrial Insulated Protective Cap provides a fully shielded, insulating cover for energized bushings.
PAGE 12
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:13 AM Page 320 200 Amp Load Break Elbows: Accessories 3M™ Industrial Loadbreak Probe Replacement Kit Voltage 5-15 kV Current 200 Ampere Component Type Accessory/Elbow Compatible With Order No. UPC LBP-15 054007-04825 Loadbreak Elbow Probe, 15 kV 200 Amp. Field replaceable, tin plated copper probe ensures reliable elec- 3M Industrial trical connection.
PAGE 13
IronwoodPremium_243240_Catalog-On-Demand.QXD 7/11/2013 7:13 AM Page 321 600 Amp Dead Break T-Bodies The 3M™ 600 Amp T-Bodies 5815 Series is a fully shielded 600 amp separable connector system which meets the requirements of ANSI/IEEE Standard 386, "Separable Insulated Connector Systems." These modular kits are available for splicing, dead-ending and connecting to dead-front apparatus such as transformers, switches and switchgear equipped with 600 amp bushings.
PAGE 14
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 15
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 16
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 17
IronwoodPremium_243240_Catalog-On-Demand.
PAGE 18
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 326 600 Amp Dead Break T-Bodies: Accessories 3M™ Cold Shrink Shield Adapter Kits 8459/8460 Series 3M™ Cold Shrink Shield Adapter Kits are designed for grounding and sealing tape shield, wire shield and Unishield® power cables when using cable accessories such as elbows, modular splices and terminations. The Shield Adapter Kit design provides a fault current capacity of 600 amps on 15–35 kV class cables.
PAGE 19
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 327 600 Amp Dead Break T-Bodies: Accessories The 3M™ Modular Splicing Kit 5815-S Kit, your basic splice, is for two-way shielded power cable connections. The 5815-S is easy to disconnect, without affecting integrity, while adding or removing cables. It is also an excellent alternative to expensive switches when isolating circuits for maintenance. The “square corner” configuration saves space.
PAGE 20
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 328 600 Amp Dead Break T-Bodies: Accessories 3M™ Dead-End Modular Kit 5815-D Use the 3M™ Dead-End Modular Kit 5815-D for plan-ahead cable systems including submersible dead-end for cables put down during site construction. Each kit contains 1 tee-module, 2 dead-end plugs, 1 connecting stud, 1 instruction booklet and silicone lubricant. A cable adapter kit is required for each cable.