Cut Sheet

ManualsBrands3M ManualsConnectorsMotor Lead Splicing Kit (3 splices/kit)

PHONE: 800-245-3573 www.3M.com/Electrical 329

Motor Lead Connections

3M provides a convenient kit with sufficient

material needed to quickly make lugged

motor lead connections to feeder cables.

Each kit makes three splices and is

designed exclusively for the abrasion,

moisture, grime and temperature extremes

of the industrial environment. 3M™ Motor

Lead Connectors meet requirements for

CSA certification and NRTL certification.

Low Voltage Motor Leads–Pigtail and

Inline for 1 kV

Motor lead pigtail connections (5300

through 5304) and inline splices (5311 through 5314) are designed to splice 1000 V or less, non-shielded

feeder and motor lead cable. The splices are made with a slip-on lug cover made of EPDM rubber. Use

with one-hole lug only. Each kit makes three splices.

Medium Voltage Motor Leads–Pigtail for Nonshielded 5–8 kV

Motor lead pigtail connections (5316 through 5319) are designed to splice 5–8 kV non-shielded feeder

and motor lead cables. The splices are made with a slip-on lug cover made of EPDM rubber. Use with one-

or two-hole copper lugs. Each kit makes three splices.

Medium Voltage Motor Leads–Pigtail and Inline for 5–8 kV

Motor lead pigtail connections (5321 through 5324) and inline splices (5331 through 5334) are designed

to splice 5–8 kV shielded (tape shield, wire shield and UniShield®) and non-shielded feeder cable. The

splices are made with a slip-on lug cover made of EPDM rubber. Use with one- or two-hole lugs. Each kit

makes three splices.

Medium Voltage Motor Leads with High-K Stress Control–Pigtail or V-Stub Splice for 5–8 kV

Shielded and Nonshielded Cables

3M™ Motor Lead Splicing Kits 5380 Series are designed for splicing motor lead cables to incoming feeder

cables. These kits are removable and reusable. These kits can accommodate pigtail (stub) connections,

5/8 kV shielded and non-shielded feeders. The splice’s main component, the lug cover, is made from

Motor Lead Connections

IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 329

Summary of content (8 pages)

PAGE 1
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 329 Motor Lead Connections Motor Lead Connections 3M provides a convenient kit with sufficient material needed to quickly make lugged motor lead connections to feeder cables. Each kit makes three splices and is designed exclusively for the abrasion, moisture, grime and temperature extremes of the industrial environment. 3M™ Motor Lead Connectors meet requirements for CSA certification and NRTL certification.
PAGE 2
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 330 EPDM rubber as a slip-on insulator. Mastic is used for the moisture seal on the pigtail kits. The kits utilize a high dielectric constant (K) stress control termination and slip-on lug cover for the feeder cable’s electrical stress control. These kits are designed to be used with copper compression lugs.
PAGE 3
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 331 Low Voltage Motor Leads, 1 kV and less 3M™ Motor Lead Pigtail Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of pigtail (stub) connections at 1000 volts and less. The splice’s main component, the slip-on lug cover, is made from EPDM rubber. Mastic strips are used for the moisture seal.
PAGE 4
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 332 Low Voltage Motor Leads, 1 kV and less 3M™ Motor Lead Inline Splice Kits, 1-Hole Lug Connections, 5311–5314 3M™ Motor Lead Inline Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of inline connections at 1000 volts and less. The splice’s main component, the slip-on splice cover, is made from EPDM rubber. A mastic strip is used for the moisture seal.
PAGE 5
IronwoodPremium_243240_Catalog-On-Demand12.QXD 7/11/2013 7:31 AM Page 333 Medium Voltage Leads, 5–8 kV 3M™ Motor Lead Pigtail Splicing Kits 5300 Series are a series of kits designed for splicing motor lead cables to incoming feeder cables, including pigtail (stub) connections at 1000 volts or less, as well as 5/8 kV non-shielded feeders. The splice’s main component, the slip-on splice cover, is made from EPDM rubber. A mastic strip is used for the moisture seal.
PAGE 6
IronwoodPremium_243240_Catalog-On-Demand13.QXD 7/11/2013 7:31 AM Page 334 Medium Voltage Leads, 5–8 kV 3M™ Motor Lead Pigtail Splice Kits, Shielded and Non-Shielded Cables, 5321-5324 3M™ Motor Lead Pigtail Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables. These kits can accommodate pigtail (stub) connections of 5/8 kV with shielded feeders. The splice’s main component, the slip-on splice cover, is made from EPDM rubber.
PAGE 7
IronwoodPremium_243240_Catalog-On-Demand13.QXD 7/11/2013 7:31 AM Page 335 Medium Voltage Leads, 5–8 kV 3M™ Motor Lead Inline Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables. 3M™ Motor Lead Splicing Kits 5331-5334 can accommodate inline connections, 5/8 kV shielded and non-shielded feeders. The splice’s main component, the slip-on splice cover, is made from EPDM rubber. A mastic strip is used for the moisture seal on the inline kits.
PAGE 8
IronwoodPremium_243240_Catalog-On-Demand13.QXD 7/11/2013 7:31 AM Page 336 Medium Voltage Leads, 5–8 kV 3M™ Motor Lead Pigtail or V-Stub Splice, Shielded and Non-Shielded Cable, 5380 Series 3M™ Motor Lead Pigtail Splicing Kits 5380 Series are designed for splicing motor lead cables to incoming feeder cables. These kits are removable and reusable. These kits can accommodate pigtail (stub) connections, 5/8 kV shielded and non-shielded feeders.