MSDS

ManualsBrands3M ManualsTools & Hardware16.9 fl. oz. Marine Mildew Block

3M MARINE MILDEW BLOCK, PN 09065 03/31/15

_________________________________________________________________________________________

Page 1 of 12

Safety Data Sheet

allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from

3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

22-8254-9

Version Number:

6.00

Issue Date:

03/31/15

Supercedes Date:

10/19/11

SECTION 1: Identification

1.1. Product identifier

3M MARINE MILDEW BLOCK, PN 09065

Product Identification Numbers

LB-T100-0514-0, 60-4550-3530-7, 60-9801-0733-2

1.2. Recommended use and restrictions on use

Recommended use

Protection against mildew, Marine

1.3. Supplier’s details

MANUFACTURER:

DIVISION:

Marine & Specialty Vehicle

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or (651) 737-6501 (24 hours)

SECTION 2: Hazard identification

The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200.

This information may be different from the actual product label information for labels regulated by other agencies.

2.1. Hazard classification

Summary of content (12 pages)

PAGE 1
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Safety Data Sheet Copyright,2015,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
PAGE 2
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Skin Sensitizer: Category 1. 2.2. Label elements Signal word Warning Symbols Exclamation mark | Pictograms Hazard Statements May cause an allergic skin reaction. Precautionary Statements General: Keep out of reach of children. Prevention: Avoid breathing dust/fume/gas/mist/vapors/spray. Wear protective gloves. Contaminated work clothing must not be allowed out of the workplace. Response: IF ON SKIN: Wash with plenty of soap and water.
PAGE 3
M MARINE MILDEW BLOCK, PN 09065 03/31/15 Ingredient Water NJTSRN# 71-091799 Styrene Acrylic Copolymer Emulsion less Water Additives and Residuals Styrene/Acrylic Copolymer Tri(Butoxyethyl) Phosphate (3-Aminopropyl)Triethoxysilane C.A.S. No. 7732-18-5 Trade Secret* % by Wt 60 - 100 Trade Secret * 1 - 5 Trade Secret * Trade Secret* Trade Secret* 78-51-3 919-30-2 1 - 5 Trade Secret * 1 - 5 Trade Secret * 0.5 - 1.
PAGE 4
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 5.3. Special protective actions for fire-fighters No special protective actions for fire-fighters are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2.
PAGE 5
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Full Face Shield Safety Glasses with side shields Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment.
PAGE 6
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Flammable Limits(UEL) Vapor Pressure Not Applicable 20 mmHg [@ 70 ºF] Vapor Density No Data Available Density Specific Gravity 1.05 g/ml 1.
PAGE 7
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority.
PAGE 8
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification.
PAGE 9
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Skin Sensitization Name (3-Aminopropyl)Triethoxysilane Species Guinea pig Value Sensitizing Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity For the component/components, either no data are currently available or the data are not sufficient for classification.
PAGE 10
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Dispose of waste product in a permitted industrial waste facility.
PAGE 11
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 15.2. State Regulations Contact 3M for more information. 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
PAGE 12
3M MARINE MILDEW BLOCK, PN 09065 03/31/15 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application.