user manual
Table Of Contents
- Contents
- About This Guide
- Overview
- Starting Up
- Integrated Fast Setup
- Using the Local Management Application
- Configuring the Platform
- Password Setup
- Setting Up for Management
- Display Current IP Configuration
- Update IP Address
- Display Current NMS IP Address
- Update NMS Address
- Display Current Default Gateway IP Address
- Update Default Gateway IP Address
- Display Current IP Subnet Mask
- Update IP Subnet Mask
- Display Current Read Community String
- Update Read Community String
- Display Current Write Community String
- Update Write Community String
- Display Ethernet Encapsulation Type
- Update Ethernet Encapsulation Type
- Set Management Configuration to Factory Defaults
- Setting the Port Network Connection Type
- Resetting All Parameters
- Downloading System Software
- Managing Switch Fabric Modules
- Configuring Interface Modules
- Logging Out and Rebooting
- ATM Features and Software Versions
- LECS ATM Address
- Setting Up the Switch Clock Source
- Managing Network Interfaces
- ILMI Setup
- Display ILMI Version
- Update ILMI Version
- Display Auto-configuration Status
- Update Auto-configuration Status
- Display Auto-discovery Status
- Update Auto-discovery status
- Display LECS Access Options
- Update LEC/LECS Communication Channel
- Display ILMI Channel Polling Status
- Update ILMI Channel Polling Status
- Display ILMI Channel Polling Interval
- Update ILMI Channel Polling Interval
- ATM Addresses Port Table
- Network Prefix
- ILMI Setup
- Configuring Virtual Channels
- Viewing Statistics
- Managing LAN Emulation
- LAN Emulation Setups
- LAN Emulation Services Setup
- LAN Emulation Redundancy Setup
- LANE Version of Switch
- MPOA Devices Configuration
- Display Current MPS Configuration
- Set Keep-Alive Time
- Set Keep-Alive Lifetime
- Set Internetwork Layer Protocols
- Set Initial Retry Time
- Set Retry Time Maximum
- Set Give Up Time
- Set Default Holding Time
- Display Current MPC Configuration
- Set Shortcut Setup Frame Count
- Set Shortcut Setup Frame Time
- Set Flow Detection Protocols
- Set Initial Retry Time
- Set Retry Time Maximum
- Set Hold Down Time
- LAN Emulation Configuration Service (LECS) Operations
- LECS Address
- LECS Search Policy
- LECS ELAN Database Operations
- Display ELANs
- Display ELAN Parameters in LECS Database
- Update ELAN Parameters in LECS Database
- Display ELAN MAC Addresses
- Delete ELAN MAC Address
- Add ELAN MAC Address
- Display ELAN ATM Addresses
- Delete ELAN ATM Address
- Add ELAN ATM Address
- Add ELAN
- Delete ELAN
- Configure Segment ID
- LECS Database Statistics
- Reset LECS
- Display LECS Maximum Connection Number
- Update LECS Maximum Connection Number
- LAN Emulation Redundancy
- LAN Emulation Service (LES) Operations
- LES Address
- ELAN Parameters
- LE_ARP Policy Configuration
- Display ELAN Response Policy
- Update ELAN Response Policy
- Display LE_ARP Response Policy
- Update LE_ARP Response Policy
- Display LE_ARP Response Policy for Route Descriptor
- Update LE_ARP Response Policy for Route Descriptor
- Reset LES Configurations
- Display LANE Multicast Forward Delay
- Update LANE Multicast Forward Delay
- LEC Operations
- LAN Emulation Statistics
- LAN Emulation Setups
- LEC ELAN Admission Security
- Configuring and Managing PNNI
- Viewing the Current PNNI State
- Configuring PNNI Nodes
- Get Number of Nodes
- Get Enhanced 164 Address Support State
- Set & Save Enhanced E.164 Address Support State
- Get Node Index
- Get Node Administrative Status
- Set Node Administrative Status to UP
- Set Node Administrative Status to DOWN
- Purge PNNI Database
- Get Node Level
- Set Node Level
- Get ATM Address
- Set Default ATM Address
- Set ATM Address
- Get Peer Group ID
- Set Peer Group ID
- Get Node ID
- Set Default Node ID
- Set Node ID
- Get Node Name
- Set Node Name
- Get PGL Priority
- Set PGL Priority
- Setting the Timers
- Set PTSE Holddown Timer
- SetHello Holddown Timer
- Set Hello Interval
- Set Hello Inactivity Factor
- Set PTSE Refresh Interval
- Set PTSE Lifetime Factor
- Set Retransmit Interval
- Set Peer Delayed ACK Interval
- Set AvCR Proportional Multiplier (%)
- Set AvCR Minimum Threshold (%)
- Set CDV Proportional Multiplier (%)
- Set CTD Proportional Multiplier (%)
- Set SVCC Initiation Time
- Set SVCC Retry Time
- Set SVCC Calling Integrity Time
- Set SVCC Called Integrity Time
- Set All Timers to Their Default Values
- Setting Optimization Metrics
- Setting Interface Parameters
- Managing the Scope Mapping Table
- Configuring the Route Cache
- Showing PNNI Information
- ATM Switch Fabric Module Specifications
- Menu Index
- Technical Support
- Glossary
- Index
- 3Com Corporation Limited Warranty
236
C
HAPTER
9: M
ANAGING
LAN E
MULATION
MPOA Client Configuration Parameters
Table 30 describes the MPOA Client configuration parameters.
Table 30 MPOA Client Configuration Parameters
Variable Name Description
MPC-p1 shortcut-setup frame time If an MPC forwards at least MPC-p2 frames to the same target
within any period MPC-p1 via the default forwarding path, it should
initiate the procedure to establish a shortcut. The MPC-p1 and
MPC-p2 parameters specify a default mechanism for automatically
detecting flows in the absence of other information. Other
mechanisms (e.g. RSVP) may be used in specific cases to override
this default.
(Minimum = 1 sec., default = 1 sec., maximum = 60 sec.)
MPC-p2 shortcut-setup frame count See MPC-p1.
(Minimum = 1 sec., default = 10 sec., maximum = 65535 sec.)
MPC-p3 flow detection protocols A set of protocols on which to perform flow detection.
Default = ().
MPC-p4 MPC initial retry time Initial retry time used by the MPOA retry mechanism.
(Minimum = 1 sec., default = 5sec., maximum = 300 sec.)
MPC-p5 MPC retry time maximum Maximum retry time used by the MPOA retry mechanism.
(Minimum = 10 sec., default = 40 sec., maximum = 300 sec.)
MPC-p6 hold down time Minimum time to wait before reinitiating a failed resolution
attempt. This is usually set to a value greater than MPC-p5.
(Minimum = 30 sec., default = MPC-p%*4, maximum = 120 sec.)