- LG Software Innovations Coffeemaker User Manual
Table Of Contents
- Title Page
- Revision history
- Contents
- About this guide
- Description
- System requirements
- List of ITG ISDN components
- Ordering rules and guidelines
- ITG ISL Trunk card description
- ITG ISL Trunk card physical description
- ISDN Signaling Link
- Dialing plans
- Quality of Service
- Fallback to alternate facilities
- Type of Service
- Fax support
- Remote Access
- Per-call statistics support using RADIUS Client
- SNMP MIB
- Codec profiles
- Security passwords
- ITG Engineering Guidelines
- Introduction
- Network engineering guidelines overview
- ITG traffic engineering
- Configuration of Meridian 1 routes and network translation
- Assess WAN link resources
- QoS Evaluation Process Overview
- Set QoS
- Measure intranet QoS
- Implement QoS in IP networks
- ITG Trunk DSP profile settings
- Post-installation network measurements
- Estimate QoS level
- ITG MAT PC management configuration
- Install and configure ITG ISL Trunk node
- Before you begin
- Installation Procedure Summary
- Create the ITG Trunk Installation Summary Sheet
- Install and cable ITG trunk cards
- Install NTCW84JA Large System I/O Panel 50-Pin filter adapter
- Install NTMF94EA and NTCW84KA cables
- D-channel cabling for the NT0961AA 24-Port ITG Trunk card
- Set NT6D80 MSDL switches
- Install filter and NTND26 cable (for MSDL and DCHIP cards in same Large System equipment row)
- Install filter and NTND26 cable (for MSDL and DCHIP cards in different Large System equipment rows)
- Configure ITG Trunk data on the Meridian 1
- Configure dialing plans within the corporate network
- Configure ITG Trunk data on MAT
- Transmit ITG trunk card configuration data from MAT to the ITG trunk cards
- Set date and time for the ITG ISL Trunk node
- Change the default ITG shell password to maintain access security
- Change default ESN5 prefix for non-ESN5 IP telephony gateways
- Check card software
- Configure MAT Alarm Management to receive SNMP traps from ITG ISL Trunk cards
- Make test calls to the remote ITG nodes
- Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks
- Upgrade procedure summary
- Before you begin
- Install the DCHIP hardware upgrade kit
- Upgrade the 8-port ITG basic trunk software to ITG ISL trunk software
- Remove ITG 1.0 configuration data from Meridian 1
- Configure the Meridian 1 ITG ISL Trunk data: upgrade considerations
- Verify ROM-BIOS version
- Upgrade Troubleshooting
- OA&M using MAT applications
- OA&M using the ITG shell CLI and overlays
- Maintenance
- Appendix A: Calbe description and NT8D81BA cable replacement
- NTMF94EA E - LAN, T - LAN and Serial Port cable
- NTCW84KA E-LAN, T-LAN, DCH & Serial cable
- NTAG81CA Faceplate Maintenance cable
- NTAG81BA Maintenance Extender cable
- NTCW84EA DCH PC Card Pigtail cable
- NTMF04BA MSDL extension cable
- NTCW84LA and NTCW84MA upgrade cables
- Prevent ground loops on connection to external customer LAN equipment
- Replace cable NT8D81BA with NT8D81AA
- Tools list
- NT8D81BA cable removal procedures
- Appendix B: Environmental and electrical regulatory data
- Appendix C: Subnet mask conversion from CIDR to dotted decimal format
- Appendix D: Configure a Netgear RM356 modem router for remote access
- Index
- Back

Description Page 53 of
378
ITG Trunk 2.0 ISDN Signaling Link (ISL) Description, Installation and Operation
Quality of Service
Quality of Service (QoS) is the gauge of quality of the IP network between
two nodes. As QoS degrades, existing calls suffer poor voice and fax quality.
New calls will not be initiated if transmissions degrade below an acceptable
level.
Behavioral characteristics of the IP network depend on:
• Round Trip Time (RTT)
•latency
• queuing delay in the intermediate nodes
• packet loss
• available bandwidth.
The Type of Service (TOS) bits in the IP packet header can affect how
efficiently data is routed through the network. For further information on
ToS, see “Type of Service” on page 59.
Packet jitter related to latency affects the quality of real-time IP
transmissions. For good voice quality, the ITG ISL Trunk card reassembles
the voice packets in an ordered continuous speech stream and plays them out
at regular intervals despite varying packet arrival times.
The user configures a required QoS for the ITG node in MAT. The QoS value
determines when calls Fallback to alternate facilities due to poor performance
of the data network. The QoS value is between 0.0 and 5.0, where 0.0 means
never Fallback to alternate facilities, and 5 means Fallback to alternate
facilities unless the voice quality is perfect. When the QoS for outgoing calls,
as measured by the Leader card, falls below the configured value, calls
Fallback to alternate facilities. Once the QoS rises above the configured
value, all new outgoing calls are routed through the IP network.
Note: QoS is measured per remote gateway. For example, if a given
Leader has three remote leaders in its dialing plan table, it will perform
three QoS measurements and calculations (one per remote gateway).