- LG Software Innovations Coffeemaker User Manual
Table Of Contents
- Title Page
- Revision history
- Contents
- About this guide
- Description
- System requirements
- List of ITG ISDN components
- Ordering rules and guidelines
- ITG ISL Trunk card description
- ITG ISL Trunk card physical description
- ISDN Signaling Link
- Dialing plans
- Quality of Service
- Fallback to alternate facilities
- Type of Service
- Fax support
- Remote Access
- Per-call statistics support using RADIUS Client
- SNMP MIB
- Codec profiles
- Security passwords
- ITG Engineering Guidelines
- Introduction
- Network engineering guidelines overview
- ITG traffic engineering
- Configuration of Meridian 1 routes and network translation
- Assess WAN link resources
- QoS Evaluation Process Overview
- Set QoS
- Measure intranet QoS
- Implement QoS in IP networks
- ITG Trunk DSP profile settings
- Post-installation network measurements
- Estimate QoS level
- ITG MAT PC management configuration
- Install and configure ITG ISL Trunk node
- Before you begin
- Installation Procedure Summary
- Create the ITG Trunk Installation Summary Sheet
- Install and cable ITG trunk cards
- Install NTCW84JA Large System I/O Panel 50-Pin filter adapter
- Install NTMF94EA and NTCW84KA cables
- D-channel cabling for the NT0961AA 24-Port ITG Trunk card
- Set NT6D80 MSDL switches
- Install filter and NTND26 cable (for MSDL and DCHIP cards in same Large System equipment row)
- Install filter and NTND26 cable (for MSDL and DCHIP cards in different Large System equipment rows)
- Configure ITG Trunk data on the Meridian 1
- Configure dialing plans within the corporate network
- Configure ITG Trunk data on MAT
- Transmit ITG trunk card configuration data from MAT to the ITG trunk cards
- Set date and time for the ITG ISL Trunk node
- Change the default ITG shell password to maintain access security
- Change default ESN5 prefix for non-ESN5 IP telephony gateways
- Check card software
- Configure MAT Alarm Management to receive SNMP traps from ITG ISL Trunk cards
- Make test calls to the remote ITG nodes
- Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks
- Upgrade procedure summary
- Before you begin
- Install the DCHIP hardware upgrade kit
- Upgrade the 8-port ITG basic trunk software to ITG ISL trunk software
- Remove ITG 1.0 configuration data from Meridian 1
- Configure the Meridian 1 ITG ISL Trunk data: upgrade considerations
- Verify ROM-BIOS version
- Upgrade Troubleshooting
- OA&M using MAT applications
- OA&M using the ITG shell CLI and overlays
- Maintenance
- Appendix A: Calbe description and NT8D81BA cable replacement
- NTMF94EA E - LAN, T - LAN and Serial Port cable
- NTCW84KA E-LAN, T-LAN, DCH & Serial cable
- NTAG81CA Faceplate Maintenance cable
- NTAG81BA Maintenance Extender cable
- NTCW84EA DCH PC Card Pigtail cable
- NTMF04BA MSDL extension cable
- NTCW84LA and NTCW84MA upgrade cables
- Prevent ground loops on connection to external customer LAN equipment
- Replace cable NT8D81BA with NT8D81AA
- Tools list
- NT8D81BA cable removal procedures
- Appendix B: Environmental and electrical regulatory data
- Appendix C: Subnet mask conversion from CIDR to dotted decimal format
- Appendix D: Configure a Netgear RM356 modem router for remote access
- Index
- Back
OA&M using the ITG shell CLI and overlays Page 285 of
378
ITG Trunk 2.0 ISDN Signaling Link (ISL) Description, Installation and Operation
checksum is calculated to check correct delivery. When the new software
version is correctly downloaded, you must reboot the ITG card with
cardReset to run the new software.
1 Download the MAT ITG software from the World Wide Web (WWW) to
a PC hard drive. Open a browser on a PC and connect to WWW
address: http://www.nortelnetworks.com/itg
When connected to the site, enter the user name and password.
The default user name is usa
The default password is usa
2 Select the latest recommended software version and select the
location on the MAT ITG PC hard drive where it is to be downloaded.
Record the MAT ITG PC hard drive location for use later in the
procedure.
Alternatively, you can order the latest ITG software on a PC card.
Up
g
rade ITG card software b
y
PC card
The PC card can be received from Nortel Networks containing the latest
ITG card software version. You can update the ITG card software
version on the PC card by copying the file from your PC hard disk to the
PC card, which is inserted in a PCMCIA slot on your PC.
1 Insert the PC card containing the software into the A: drive of the ITG
card, located on the faceplate of the card.
2 From the ITG shell, monitor the successful insertion of the PC card.
There will be a message that indicates that the card has been
successful recognized and installed.
3 Use the swDownload command to copy the software from the PC
card to the ITG card flash ROM device, using the FTP client and the
FTP host on the card. The host name parameter in this command is
the management interface IP address of the ITG card. The user name
and password are the same as configured for the ITG shell. The
directory path, which is "/A:", and file name indicate the software file on
the PC card in the A: drive.
4 Press Enter. Monitor the status of the software upgrade, and check
that the upgrade correctly finishes. Observe any error messages that
indicate problems with parameters or syntax.