- LG Software Innovations Coffeemaker User Manual
Table Of Contents
- Title Page
- Revision history
- Contents
- About this guide
- Description
- System requirements
- List of ITG ISDN components
- Ordering rules and guidelines
- ITG ISL Trunk card description
- ITG ISL Trunk card physical description
- ISDN Signaling Link
- Dialing plans
- Quality of Service
- Fallback to alternate facilities
- Type of Service
- Fax support
- Remote Access
- Per-call statistics support using RADIUS Client
- SNMP MIB
- Codec profiles
- Security passwords
- ITG Engineering Guidelines
- Introduction
- Network engineering guidelines overview
- ITG traffic engineering
- Configuration of Meridian 1 routes and network translation
- Assess WAN link resources
- QoS Evaluation Process Overview
- Set QoS
- Measure intranet QoS
- Implement QoS in IP networks
- ITG Trunk DSP profile settings
- Post-installation network measurements
- Estimate QoS level
- ITG MAT PC management configuration
- Install and configure ITG ISL Trunk node
- Before you begin
- Installation Procedure Summary
- Create the ITG Trunk Installation Summary Sheet
- Install and cable ITG trunk cards
- Install NTCW84JA Large System I/O Panel 50-Pin filter adapter
- Install NTMF94EA and NTCW84KA cables
- D-channel cabling for the NT0961AA 24-Port ITG Trunk card
- Set NT6D80 MSDL switches
- Install filter and NTND26 cable (for MSDL and DCHIP cards in same Large System equipment row)
- Install filter and NTND26 cable (for MSDL and DCHIP cards in different Large System equipment rows)
- Configure ITG Trunk data on the Meridian 1
- Configure dialing plans within the corporate network
- Configure ITG Trunk data on MAT
- Transmit ITG trunk card configuration data from MAT to the ITG trunk cards
- Set date and time for the ITG ISL Trunk node
- Change the default ITG shell password to maintain access security
- Change default ESN5 prefix for non-ESN5 IP telephony gateways
- Check card software
- Configure MAT Alarm Management to receive SNMP traps from ITG ISL Trunk cards
- Make test calls to the remote ITG nodes
- Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks
- Upgrade procedure summary
- Before you begin
- Install the DCHIP hardware upgrade kit
- Upgrade the 8-port ITG basic trunk software to ITG ISL trunk software
- Remove ITG 1.0 configuration data from Meridian 1
- Configure the Meridian 1 ITG ISL Trunk data: upgrade considerations
- Verify ROM-BIOS version
- Upgrade Troubleshooting
- OA&M using MAT applications
- OA&M using the ITG shell CLI and overlays
- Maintenance
- Appendix A: Calbe description and NT8D81BA cable replacement
- NTMF94EA E - LAN, T - LAN and Serial Port cable
- NTCW84KA E-LAN, T-LAN, DCH & Serial cable
- NTAG81CA Faceplate Maintenance cable
- NTAG81BA Maintenance Extender cable
- NTCW84EA DCH PC Card Pigtail cable
- NTMF04BA MSDL extension cable
- NTCW84LA and NTCW84MA upgrade cables
- Prevent ground loops on connection to external customer LAN equipment
- Replace cable NT8D81BA with NT8D81AA
- Tools list
- NT8D81BA cable removal procedures
- Appendix B: Environmental and electrical regulatory data
- Appendix C: Subnet mask conversion from CIDR to dotted decimal format
- Appendix D: Configure a Netgear RM356 modem router for remote access
- Index
- Back
Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks Page 241 of
378
ITG Trunk 2.0 ISDN Signaling Link (ISL) Description, Installation and Operation
3 Press Enter.
4 The ITG shell outputs value = 0 = 0 x 0 to indicate successful
completion of the setLeader command. If the ITG shell outputs
command not found, check the spelling of the command. If the ITG
shell outputs a value of -1, contact Nortel Networks customer technical
support.
5 Return to the MAT IP Telephony Gateway - ISDN IP Trunk Main
window.
6 Telnet to Leader 1 and Follower cards in the node.
7 Log into the ITG shell.
At the ITG>prompt, enter clearLeader “xxx.xxx.xxx.xxx”,
“yyy.yyy.yyy.yyy”, ”zzz.zzz.zzz.zzz”
(see notes in step 2). The ITG shell outputs value = 0 = 0 x 0 to
indicate successful completion of the clearLeader command.
Note:
You enter clearLeader command even when you remove
configuration files from Follower cards.
Step 2 - Transmit ITG Trunk 2.0 software to the 8-port cards
1 Launch MAT/OTM 1.1. Double-click on ITG M1 IP Trk in the Services
folder
1 In the IP Telephony Gateway window, select Leader 0 from the ITG
trunk node you are upgrading.
2 Select menu Configuration | Synchronize | Transmit. The
ITG-Transmit Options window appears.
3 Make sure to set the radio button to Transmit to selected nodes.
Check the Card Software check box only.
4 Locate the ITG28xx.mms software file on the MAT PC. If you know the
path to the ITG28xx.mms software file software, type the path
information in the Software field. Or click the Browse button to find and
select the file and click the open button in the Browser so that the
software path and filename appear in the Software field in the
ITG-Transmit options window.