- LG Software Innovations Coffeemaker User Manual
Table Of Contents
- Title Page
- Revision history
- Contents
- About this guide
- Description
- System requirements
- List of ITG ISDN components
- Ordering rules and guidelines
- ITG ISL Trunk card description
- ITG ISL Trunk card physical description
- ISDN Signaling Link
- Dialing plans
- Quality of Service
- Fallback to alternate facilities
- Type of Service
- Fax support
- Remote Access
- Per-call statistics support using RADIUS Client
- SNMP MIB
- Codec profiles
- Security passwords
- ITG Engineering Guidelines
- Introduction
- Network engineering guidelines overview
- ITG traffic engineering
- Configuration of Meridian 1 routes and network translation
- Assess WAN link resources
- QoS Evaluation Process Overview
- Set QoS
- Measure intranet QoS
- Implement QoS in IP networks
- ITG Trunk DSP profile settings
- Post-installation network measurements
- Estimate QoS level
- ITG MAT PC management configuration
- Install and configure ITG ISL Trunk node
- Before you begin
- Installation Procedure Summary
- Create the ITG Trunk Installation Summary Sheet
- Install and cable ITG trunk cards
- Install NTCW84JA Large System I/O Panel 50-Pin filter adapter
- Install NTMF94EA and NTCW84KA cables
- D-channel cabling for the NT0961AA 24-Port ITG Trunk card
- Set NT6D80 MSDL switches
- Install filter and NTND26 cable (for MSDL and DCHIP cards in same Large System equipment row)
- Install filter and NTND26 cable (for MSDL and DCHIP cards in different Large System equipment rows)
- Configure ITG Trunk data on the Meridian 1
- Configure dialing plans within the corporate network
- Configure ITG Trunk data on MAT
- Transmit ITG trunk card configuration data from MAT to the ITG trunk cards
- Set date and time for the ITG ISL Trunk node
- Change the default ITG shell password to maintain access security
- Change default ESN5 prefix for non-ESN5 IP telephony gateways
- Check card software
- Configure MAT Alarm Management to receive SNMP traps from ITG ISL Trunk cards
- Make test calls to the remote ITG nodes
- Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks
- Upgrade procedure summary
- Before you begin
- Install the DCHIP hardware upgrade kit
- Upgrade the 8-port ITG basic trunk software to ITG ISL trunk software
- Remove ITG 1.0 configuration data from Meridian 1
- Configure the Meridian 1 ITG ISL Trunk data: upgrade considerations
- Verify ROM-BIOS version
- Upgrade Troubleshooting
- OA&M using MAT applications
- OA&M using the ITG shell CLI and overlays
- Maintenance
- Appendix A: Calbe description and NT8D81BA cable replacement
- NTMF94EA E - LAN, T - LAN and Serial Port cable
- NTCW84KA E-LAN, T-LAN, DCH & Serial cable
- NTAG81CA Faceplate Maintenance cable
- NTAG81BA Maintenance Extender cable
- NTCW84EA DCH PC Card Pigtail cable
- NTMF04BA MSDL extension cable
- NTCW84LA and NTCW84MA upgrade cables
- Prevent ground loops on connection to external customer LAN equipment
- Replace cable NT8D81BA with NT8D81AA
- Tools list
- NT8D81BA cable removal procedures
- Appendix B: Environmental and electrical regulatory data
- Appendix C: Subnet mask conversion from CIDR to dotted decimal format
- Appendix D: Configure a Netgear RM356 modem router for remote access
- Index
- Back
Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks Page 239 of
378
ITG Trunk 2.0 ISDN Signaling Link (ISL) Description, Installation and Operation
5 Pull the top and bottom locking devices away from the ITG faceplate.
Insert the ITG card into the card slots and carefully push it until it
makes contact with the backplane connector. Hook the locking
devices.
Install the DCHIP I/O Panel breakout cable from the upgrade
kit
The breakout cable provides one D-channel connector.
If you are installing the DCHIP upgrade kit for the NTCW80AA 8-port ITG
Trunk card, use the NTCW84MA I/O Panel breakout cable.
If you are installing the DCHIP upgrade kit for the NTCW80CA 8-port ITG
Trunk card, use the NTCW84LA I/O Panel breakout cable.
1 For the large system, locate the I/O connector that corresponds to the
leftmost card slot of the ITG 8.0 port that is undergoing the hardware
upgrade.
2 Disconnect existing ELAN and serial cables. Remove the existing I/O
panel breakout cable.
3 Install the new cable (NTCW84LA or NTCW84MA). Be sure to use the
screw provided.
4 Reconnect ELAN and serial connectors. For NTCW80CA cards, install
a shielded TLAN cable.
5 Turn to “Install filter and NTND26 cable (for MSDL and DCHIP cards
in same Large System equipment row)” on page 169 to install the
DCHIP connector and MSDL cable.
Upgrade the 8-port ITG basic trunk software to
ITG ISL trunk software
You use the MAT ITG Basic Trunk application to perform this procedure.
Once you have upgraded to MAT 6.6 or later, all the configuration data for
the ITG Trunk node will have been converted.