- LG Software Innovations Coffeemaker User Manual
Table Of Contents
- Title Page
- Revision history
- Contents
- About this guide
- Description
- System requirements
- List of ITG ISDN components
- Ordering rules and guidelines
- ITG ISL Trunk card description
- ITG ISL Trunk card physical description
- ISDN Signaling Link
- Dialing plans
- Quality of Service
- Fallback to alternate facilities
- Type of Service
- Fax support
- Remote Access
- Per-call statistics support using RADIUS Client
- SNMP MIB
- Codec profiles
- Security passwords
- ITG Engineering Guidelines
- Introduction
- Network engineering guidelines overview
- ITG traffic engineering
- Configuration of Meridian 1 routes and network translation
- Assess WAN link resources
- QoS Evaluation Process Overview
- Set QoS
- Measure intranet QoS
- Implement QoS in IP networks
- ITG Trunk DSP profile settings
- Post-installation network measurements
- Estimate QoS level
- ITG MAT PC management configuration
- Install and configure ITG ISL Trunk node
- Before you begin
- Installation Procedure Summary
- Create the ITG Trunk Installation Summary Sheet
- Install and cable ITG trunk cards
- Install NTCW84JA Large System I/O Panel 50-Pin filter adapter
- Install NTMF94EA and NTCW84KA cables
- D-channel cabling for the NT0961AA 24-Port ITG Trunk card
- Set NT6D80 MSDL switches
- Install filter and NTND26 cable (for MSDL and DCHIP cards in same Large System equipment row)
- Install filter and NTND26 cable (for MSDL and DCHIP cards in different Large System equipment rows)
- Configure ITG Trunk data on the Meridian 1
- Configure dialing plans within the corporate network
- Configure ITG Trunk data on MAT
- Transmit ITG trunk card configuration data from MAT to the ITG trunk cards
- Set date and time for the ITG ISL Trunk node
- Change the default ITG shell password to maintain access security
- Change default ESN5 prefix for non-ESN5 IP telephony gateways
- Check card software
- Configure MAT Alarm Management to receive SNMP traps from ITG ISL Trunk cards
- Make test calls to the remote ITG nodes
- Upgrade an ITG Trunk 1.0 node to support ISDN signaling trunks
- Upgrade procedure summary
- Before you begin
- Install the DCHIP hardware upgrade kit
- Upgrade the 8-port ITG basic trunk software to ITG ISL trunk software
- Remove ITG 1.0 configuration data from Meridian 1
- Configure the Meridian 1 ITG ISL Trunk data: upgrade considerations
- Verify ROM-BIOS version
- Upgrade Troubleshooting
- OA&M using MAT applications
- OA&M using the ITG shell CLI and overlays
- Maintenance
- Appendix A: Calbe description and NT8D81BA cable replacement
- NTMF94EA E - LAN, T - LAN and Serial Port cable
- NTCW84KA E-LAN, T-LAN, DCH & Serial cable
- NTAG81CA Faceplate Maintenance cable
- NTAG81BA Maintenance Extender cable
- NTCW84EA DCH PC Card Pigtail cable
- NTMF04BA MSDL extension cable
- NTCW84LA and NTCW84MA upgrade cables
- Prevent ground loops on connection to external customer LAN equipment
- Replace cable NT8D81BA with NT8D81AA
- Tools list
- NT8D81BA cable removal procedures
- Appendix B: Environmental and electrical regulatory data
- Appendix C: Subnet mask conversion from CIDR to dotted decimal format
- Appendix D: Configure a Netgear RM356 modem router for remote access
- Index
- Back
Install and configure ITG ISL Trunk node Page 227 of
378
ITG Trunk 2.0 ISDN Signaling Link (ISL) Description, Installation and Operation
Transmit new software to ITG Trunk cards
Verify that the ITG Trunk cards are disabled in the Meridian 1 before
transmitting new card software.
Note: Disable ITG Trunk cards when transmitting card properties or
new software.
Use the MAT Maintenance Windows, the MAT System Passthru terminal, or
use a Meridian 1 system management terminal directly connected to a TTY
port on the Meridian 1. Use the overlay 32 DISI command to disable the ITG
cards when idle. NPROG indicates that all units on the card have been
disabled. In the MAT IP Telephony Gateway - ISDN IP Trunk main window,
select
View | Refresh
and verify that the card status is showing “Disabled”.
If the card status shows “unequipped,” configure the card in LD14.
1 Open MAT. Click on Services and launch the ITG ISDN IP Trunks
application.
2 Select the node to upgrade from the list in the upper half of the
IP
Telephony Gateway - ISDN IP
Trunk Main window.
3 Select node or cards for software transmission according to card
density:
a If all cards in the node have same card density (24-port or 8-port),
you upgrade all the cards together by transmitting to the selected
node. Click new node in upper half of the IP Telephony Gateway
- ISDN IP Trunk Main window.
b If you have a mix of 24-port and 8-port cards in the same ITG ISL
Trunk node, then select all cards of the same density in the lower
half of the Main Window. Hold down the Ctrl key while you make
individual card selections.
4 Select menu Configuration/Synchronize/Transmit. The ITG -
Transmit Options dialog box appears.