OLYMPUS DIAGNOSTIC SYSTEMS GROUP AU2700 & AU5400 ON-LINE SPECIFICATIONS -1-
AU2700/5400 Online Specifications Issued: 2000.3.16 Revised: 2000.6.8 Olympus Optical Co., Ltd.
Table of contents page 1. Outline..............................................................................................................................................................................................4 2. Basic Specification ...........................................................................................................................................................................5 2.1 Format of Transmission.................................................................
1. Outline 1) The following data is exchanged between the AU2700/5400 and the host computer system. (1) Test Requisition Information (T.R.I.) (2) Test Results 2) The data transmission is conducted in either of the following mode: (1) Class A Transmission is without synchronizing with analysis. This mode does not utilize the ACK/NAK protocol. (2) Class B Transmission is synchronizing with analysis. This mode does utilize the ACK/NAK protocol.
(2.1) Format of Transmission Item Transmission line Synchronization Contents RS-232C Data transmission mode Bit/sec Configuration Half-Duplex Synchronization 4800bps, 9600bps start bit data bit parity bit stop bit total 1 bit 7 or 8 bit none, odd or even 1 or 2 bit 9-12 bit These can be selected by [PARAMETER] [ONLINE] [PROTOCOL] menu. Form of Transmission Use channel Retry (2.2) Class A Transmission are conducted from the sender to the receiver in a certain time of interval.
(2.3) Text format (1) Basic configuration as follows: 1) 2) 3) 4) Name 1) Text start code 2) Text Classification Digit 1,2 2 Contents 01h-1Fh R# RB R_ * RH RE S# S_ * SH SE D# DB D_ * DH DR DA d_ * dH DQ DE 3) Unit No. 5) 6) Data start code T.R.I. inquiry Start of T.R.I. inquiry T.R.I. inquiry of normal sample T.R.I. inquiry of rerun sample End of T.R.I. inquiry T.R.I. T.R.I. of normal sample T.R.I. of rerun sample Stop of T.R.I.
(2) Blocking A. Definition of Term 1) 2) 3) 4) Term Text length 5) 6) Definition Is the total number of bytes from 1) to 6). [PARAMETER] [ONLINE] [PROTOCOL] menu. Max block length [PARAMETER] [ONLINE] [PROTOCOL] menu. It is the Max length of text in one record. The length of block can be selected in online parameter menu.
B. Kind of text and blocking Kind Fixed length Text Variable length text Kind of text • Start of T.R.I. inquiry • T.R.I. inquiry text • End of T.R.I. transmission text. • Stop of T.R.I. inquiry • Start of transfer result transmission text. • End of result transfer transmission text. • T.R.I. text • Rerun T.R.I.
3. Transmission Text Format (3.1) Common and changeable item The following can be selected by [PARAMETER] [ONLINE] [PROTOCOL] menu. Text start code 1) Unit No. 3) Common Item Text end code 5) BCC 6) Sample Type Dummy(in Test Result transmission Text) Block Identification No. Rack No./Cup Position Unit No. on the T.R.I. text (with out Rerun) ANL unit No. and Cuvette side on Test Result transmission Text (without RB,ACAL,QC) Space Code before the Text Classification (S,R,D text) Reagent Lot No.
(3) Repeat run inquiry test requisition. 1) R H 3) Rack No. Cup Position Sample no. Sample type (4) End text to inquiry test requisition.
(3.3) T.R.I. text (1) Normal sample test requisition information text. 1) S _ Rack No. cup position Sample no. Sample ID _ Sample type s e x age month Patient Information 4 Test code Test code Test code Patient Information 2 Patient Information 5 Patient Information 6 Test code Test code _ Block Identification No. Patient Information 1 Test code Dummy _ _ Test code Patient Information 3 Test code 5) 6) (2) Repeat run sample test requisition information text. 1) S H Rack no.
(3) End of T.R.I. Text transmission. 1) S E 5) 6) (3.4) Test result transmission text (1) Start of test result transmission text.
(2) Normal sample test result text. 1) D _ 3) Cup Position Rack no. Sample no. Sample ID Sample type S e x Age Month Patient Information 4 Patient Information 2 Patient Information 5 Patient Information 6 Blocking R1 Bottle No. R2 Lot No. R2 Bottle No. Cuvette side ANL unit No. Blocking Test Result Flags 5) 6) - 13 - _ Block Identification No. Patient Information 1 Test code R1 Lot No.
(3) Stat(fast) test result text (AU2700 only). 1) d _ 3) Cup Rack no. Posi_ _ _ _ tion 1-22 S e x Age Month Patient Information 4 P n n n Sample no. Sample ID Sample type Patient Information 2 Patient Information 5 Patient Information 6 Blocking R1 Bottle No. R2 Lot No. R2 Bottle No. Cuvette side ANL unit No. Blocking Test Result Flags 5) 6) - 14 - _ Block Identification No. Patient Information 1 Test code R1 Lot No.
(4) Emergency(fast) test result text (AU2700 only). 1) d _ 3) Cup Rack no. Posi_ _ _ _ tion 1-22 S e x Age Month Patient Information 4 E n n n Sample no. Sample ID Sample type Patient Information 2 Patient Information 5 Patient Information 6 Blocking R1 Bottle No. R2 Lot No. R2 Bottle No. Cuvette side ANL unit No. Blocking Test result Flags 5) 6) - 15 - _ Block Identification No. Patient Information 1 Test code R1 Lot No.
(5) Repeat run result text -1 . 1) D H 3) Rack no. Cup Position Sample no. Sample ID Sample type Block Identification No. Blocking Test code R1 Lot No. R1 Bottle No. R2 Lot No. R2 Bottle No. Cuvette side ANL unit No. Blocking Test result Flags 5) 6) - 16 - Original Sample no.
(6) Repeat run result text -2 Stat fast sample (AU2700 Only) . 1) d H 3) Rack no. _ _ _ _ Cup Position 1-22 P n n n Sample no. Sample ID Sample type Block Identification No. Blocking Test code R1 Lot No. R1 Bottle No. R2 Lot No. R2 Bottle No. Cuvette side ANL unit No. Blocking Test result Flags 5) 6) - 17 - Original Sample No.
(7) Reagent blank result text. 1) D R 3) _ _ _ _ _ _ Sample no. Sample type This dummy is same ID digits and assigned area is decided associated with the rack No. _ _ _ _ _ _ Dummy _ _ _ Block Identification No. ANL unit No. Cuvette side Test code R1 Lot No. R1 Bottle No. R2 Lot No. 1:First data 2:Second data Test Result Flags 5) 6) - 18 - R2 Bottle No.
(8) Acal (Calibration) result text. 1) D A 3) _ _ _ _ _ _ Sample no. This dummy spaces is assigned in case rack No. exists and assigned area is decided associated with the rack No. Calibrator ID Calibrator No. (1-80) Block Identification No. ANL unit No. Cuvette side Blocking Test Code R1 Lot No. R1 Bottle No. R2 Lot No. R2 Bottle No.
(9) QC (Quality Control) result text. 1) D Q 3) _ _ _ _ _ _ Sample no. Control ID This dummy No. is assigned in case rack No. exists and assigned area is decided associated with the rack No. Control No. Block Identification No. ANL unit No. Cuvette side Blocking Test code R1 Lot No. R1 Bottle No. R2 Lot No. R2 Bottle No. Blocking Test result Flags 5) 6) (10) End of test result transfer text.
(3.5) Relation between real-time/batch and Transmission text • • T.R.I. inquiry of Routine, Emergency, Stat and Repeat run can be selected as real-time or batch. Test results of all samples can be selected as real-time or batch.
(3.6) Others (1) Contents and formats of text. Item 1. Rack No. Digit 4 or 5 (Optional) Contents '0001'-'9999' or '00001'-'99999' STAT sample is space When Rack no. is no setting, Rack No. is '00000'. 2. Cup position (Optional) 2 rack : '01'-'10' STAT : '01'-'22' 3. Sample type 1 4. Sample No. 4 5.
9.ANL unit No. 1 (Optional) ‘1’: AU5400 ISE ‘1’: AU5400 unit 1 ‘2’: AU5400 unit 2 ‘3’: AU5400 unit 3 ‘1’: AU2700 10.Cuvette side 1 (Optional) 11. Sex AU5400 ‘0’ : inner cuvette (ISE Cell 1) ‘1’ : outer cuvette (ISE Cell 2) AU2700 ‘0’ : inner cuvette(ISE) ‘1’ : outer cuvette 1 M : male F : female SP : none sex 0 : no-set 12. Age (Optional) 13. Month (Optional) 14. Patient Information (Optional) 15. Online Test No.
17. Test result 8 or 11 Test Result digits can be 6 or 9. Flags digits is 2. • Refer to Appendix 1 (Flags List) • 18. Lot No. and Bottle No. (Optional) Remark *1: 4*4 Number or character • 0 suppress can be selected/canceled in online parameter menu Number of digits can be changed to 6 or 9 in online parameter menu. This option can be selected in the [PARAMETER] [ONLINE] [PROTOCOL] [SPECIAL] menu. If only age is the space in the text from a host, AU2700/AU5400 will output an error.
(2) Test result format. A. Test result • 0 Data digit is 6 and 0 suppress is not used. 1 2 • - • 4 1 2 3 . 4 5 6 Data digit is 6 and 0 suppress is used. _ • - . Data digit is 9 and 0 suppress is not used. 0 - 3 1 2 3 4 Data digit is 9 and 0 suppress is used. _ 1 2 3 .
B. LIH result • Data digit is 6 and 0 suppress is not used. LIP ICT HEM 0 0 0 0 NORMAL 1+ 2 ++ 3 +++ 4 ++++ 5 +++++ 6 ABN 9 Test not performed. • FLAG Data digit is 9 and 0 suppress is not used. LIP 0 0 ICT 0 0 HEM 0 0 0 NORMAL 1+ 2 ++ 3 +++ 4 ++++ 5 +++++ 6 ABN 9 Test not performed.
• Data digit is 6 and 0 suppress is used. LIP ICT _ _ HEM _ 0 NORMAL FLAG 1+ 2 ++ 3 +++ 4 ++++ 5 +++++ 6 ABN 9 Test not performed. • LIP _ _ Data digit is 6 and 0 suppress is used. ICT _ _ HEM _ _ 0 NORMAL 1+ 2 ++ 3 +++ 4 ++++ 5 +++++ 6 ABN 9 Test not performed.
(3) T.R.I. of calculated tests. Note: Calculated Test No. in T.R.I. from Host is ignored. The tests that create the calculated tests can only be ordered from the Host. (4) Data format that Test result data is digit over. a. Data digit is 6. 9 9 9 9 9 9 • Data digit is 9. 9 9 9 9 9 9 9 9 9 (5) Data format that Test result data is OD-value. • Data digit is 6. 0 . 1 2 3 4 When the data is negative OD-value, it is same as digit over. • Data digit is 9. - 0 .
(6) T.R.I of LIH. In any case, LIH test no. in T.R.I from Host is necessary for LIH analysis. LIH Reagent Test Name LIH LIH Measure All Even if AU2700/AU5400 does not have the request from a host, it performs LIH analysis. Select AU2700/AU5400 performs LIH analysis according to the request from a host. Other All Even if AU2700/AU5400 does not have the request from a host, it performs LIH analysis. No LIH analysis is not performed even if AU2700/AU5400 has the request from a host.
4. Transmission Protocols (4.1) Protocols at AU2700/5400 (1) Class A: without ACK/NAK exchange. A. Sending Text to be sent: T.R.I. Inquiry text Repeat Run T.R.I. Inquiry text Start of Test Result Transmission text Test Result text Repeat Run Result text End of Test Result Transmission text Initial Condition Start of Text Block end (BCC) Transmission text Text end (BCC) B. Receiving Text to be received: T.R.I. text Repeat Run T.R.I. text End of T.R.I.
(2) Class B: with ACK/NAK protocol. A. Sending Text to be sent: T.R.I. Inquiry text Repeat Run T.R.I.
B. Receiving Test to be sent: T.R.I. text Repeat Run T.R.I. text End of T.R.I.
(4.2) Timing/time-out (1) Time-out/timing list . Kind Description T1 Limit time from end of transfer/receive to start of text receive. T2 Limit time from start of text receive to end of text receive. T3 Limit time from start of text transfer to end of text transfer. T4 Limit time from end of text transfer to response of receive. T5 Interval time of transmission T6 Min. time from receive T7 Limit time from NAK response to start receive of retry text. t1 Min.
C.
(4.
(5) Case 5 (Abnormal Case 2) A A AU2700/5400 Host N A K N A K
5. Application Protocol (5.1) Receiving T.R.I. (1) Trans./receive sequence in one session. General sequence : A. Example 1 Shift next Rx-transfer when Online Error occurred. RB Rx Rx Rx AU2700/5400 ･･･ 0 E 0 E Sx Sx Sx Sx Host SE In case 2 blocks B. Example 2 Stop the session when Online Error occurred. RB Rx Rx RE AU2700/5400 ･･･ 0 E 0 E Sx Sx Sx Sx Host (2) Detail T.R.I.
Receive Kind of text Real-time Sx SE RE (request end) Batch RB (request start) R_ * (request Normal) Request of sample no. RH (request rerun) Request of sample no. Sx Timing/condition This text can be received after end of Rx-transfer within the designated time. This text is transferred when shifting to the modes below. 1) measure mode to standby mode 2) measure mode to stop mode This text is transmitted when the communication is canceled by the online alarm. This text is transmitted when receiving T.
(3) Kind of T.R.I. transfer/receive. A. T.R.I. of normal sample Setting of parameters Receive T.R.I.. inquiry Real-time Method of T.R.I. inquiry & T.R.I. Method of T.R.I. inquiry Sequential Rack no. Kind of T.R.I. Request of sample no Sample ID Batch Request of sample ID Request of sample no Sequential Rack no. T.R.I. inquiry Sample no T.R.I. Sample no *1 Sample no (Calculated rack No. and cup pos. No.) Sample ID Sample no *1 Sample no.
(5.2) Sending test result protocol (1) Transfer sequence for one session. General sequence : A. Example 1 Shift next Dx-transfer when Online Error occurred. DB Dx Dx Dx Dx Dx 0 E 0 E E DE AU2700/5400 2 blocks Host B. Example 2 Stop session when Online Error occurred. DB Dx Dx Dx Dx Dx 0 E 0 E E DE AU2700/5400 Host (2) Detail Data Trans.
Data Trans. Batch Kind of text DB (start) Dx (result data) DE (end) Timing/condition This text is transmitted when it selected the start of transmission in the online menu. Normal end It is shifting the transfer of the test Results. This text is transmitted at the designate time intervals. The text are the samples that is selected in the online menu It is shifting next The transfer of Dx/DE. This text is transmitted when it was transmitting the sample No.
(5.3) Others (1) Mixing the session of the TRT inquiry and the session of the test results. A. General sequence Rx Dx Dx Rx AU2700/5400 ･･･ Host Sx Sx Sx (a) Sx (b) (2) Detail Section (a) Definition of section The start of the transmission of the text of T.R.I. inquiry -- The end of the receiving of all T.R.I. for one samples Limitation Don't transmit the Test result text.
6. Specification of Connection (6.1) In/Output signals and Terminals PC Terminal at AU2700/5400 Signal Name Abbrv. Terminal at host Direction computer (25 Pin Configuration) ------------------------------------------------------------------------------------------------------------------Ground FG 1 Data sent TxDATA 3 3 (Rx DATA) Data receive RxDATA 2 2 (Tx DATA) Signal Ground SG 5 7 (SG) Request to send RTS Clear to send CTS 7 8 Caution: RTS and CTS must be connected directly. (6.
A. Flag ( % ? # R ! U u Y y @ $ D B * & Z F G x 1 2 3 4 5 6 7 p T P N H L J K S Appendix (1) Flags list Contents Failed to evade the contamination since the detergent for evading the contamination is not enough. The sample probe is clogged with sample.
/ r e c a b ) Test not performed: test has been requisitioned but not performed due To any reason. transferred data to host edited data correct data by manual correction On-board stability over Calibration stability over or Calibration does not exist. Current reagent lot number was different from reagent lot No.
(2) Online parameters list Transmission information T.R.I.
Text information rack no. /cup position rack no. digit Contents use/none 4/5 menu [PARAMETER] [ONLINE] [PROTOCOL] menu. Sex age/month use/none use/none patient information 1 patient information 2 patient information 3 patient information 4 patient information 5 patient information 6 sample ID digits use/none digits use/none digits use/none digits use/none digits use/none digits use/none digits 4-26 digits [PARAMETER] [FORMAT] [REQUISITION FORMAT] menu. [PARAMETER] [FORMAT] [REQUISITION FORMAT] menu.
Each of the following parameters are influenced as shown below. Sample Type Dummy (Test Result Transmission Text) Block Identification No. Sequence of S.No. and S.ID in T.R.I text Sequence of S.No. and S.ID in Test result text ANL Unit No. Cuvette Side Lot No. and Bottle No.
(3) Character Table HIGH LOW 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 SH SX EX ET EQ AK BL BS HT LF H M CL CR SO SI 1 DE D1 D2 D3 D4 NK SN EB CN EM SB EC 2 3 SP 0 ! 1 " 2 # 3 $ 4 % 5 & 6 ' 7 ( 8 ) 9 * : + ; 4 5 6 @ P A Q a B R b C S c D T d E U e F V f G W g H X h I Y i J Z j K [ k 7 p q r s t u v w x y z { FS GS RS US , . / L M N O | } ~ DL < = > ? \ ] ^ _ l m n o 8 9 A B C From 20H to 7EH: These characters can be used for the Sample ID code.
(4) AU2700/5400 Online Parameter Sheet Set up T.R.I. Receive Routine Normal Routine Emergency Routine Repeat Emergency Repeat Stat Normal Stat Repeat Results Transfer Routine Normal Routine Emergency Routine Repeat Emergency Repeat Stat Normal Stat Repeat Stat Fast QC Calibration Reagent blank Upper protocol Error control T.R.I. Receive Results Transfer Lower protocol Character format Character length. Parity bit Stop bit Data format Start code 1 Start code 2 End code 1 End code 2 Text length Unit No.
Rack No. Sex AGE/MONTH patient inf. 1 patient inf. 2 patient inf. 3 patient inf. 4 patient inf. 5 patient inf. 6 ID digits Data format ZERO Suppress Sample Type Dummy Block Identification ANL unit No. Cuvette side Sequence of S.No. and S.ID in T.R.I text Sequence of S.No. and S.ID in Test result text Lot No. and Bottle No. none 4 yes no yes no yes[ ]digits yes[ ]digits yes[ ]digits yes[ ]digits yes[ ]digits yes[ ]digits [ ]digits (4-26) 6 9 yes no yes no yes no yes no yes no yes no No. S.
(5) ONLINE ALARM LIST 1)ONLINE ERROR [ aa ] [ bbbbbbbbb ] (1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive has been designated as "STOP", then the following will occur: 1) Text following the alarm will not be received. 2) In a case when the text requisition is received real-time,the "STOP" status is ignored at the start of the next analysis and the text requisition will be received real-time again. (2). In the Online Parameter menu, submenu Error Control, if the T.
RH U_ xxxxxxxxxxx: repeat run, urine sample, sample ID RH UE xxxxxxxxxxx: repeat run, urine emergency sample, sample ID RH UP xxxxxxxxxxx: repeat run, urine STAT sample, sample ID RH X_ xxxxxxxxxxx: repeat run, emergency sample, sample ID RH XE xxxxxxxxxxx: repeat run, emergency sample, sample ID RH XP xxxxxxxxxxx: repeat run, STAT sample, sample ID ---------------------------------------------------------------- - 53 -
2)ONLINE ERROR [ aa ] [ bbbbbbbbb ] (1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive is designated as "STOP", the following events can occur: 1). The text following the alarm will not be received. 2). In a case when the text requisition is received real-time,the "STOP" designation is ignored and the text requisition will be received in real-time at the start of the next analysis. (2). In the Online Parameter menu, submenu Error Control, if the T.R.I.
RH _P xxxxxxxxxxx: repeat run, STAT sample, sample ID RH U_ xxxxxxxxxxx: repeat run, urine sample, sample ID RH UE xxxxxxxxxxx: repeat run, urine emergency sample, sample ID RH UP xxxxxxxxxxx: repeat run, urine STAT sample, sample ID RH X_ xxxxxxxxxxx: repeat run, Other normal sample, sample ID RH XE xxxxxxxxxxx: repeat run, Other emergency sample, sample ID RH XP xxxxxxxxxxx: repeat run, Other STAT sample, sample ID ---------------------------------------------------------------- - 55 -
3)ONLINE FORMAT ERROR <> (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for samples following the alarm. <> (1).In the Online Parameter menu, submenu Set Up, the T.R.I. receive is not designated asn "YES" for the necessary parameter. (2).The display in the [ ] and its meaning are as follows.
4)ONLINE ILLEGAL TEXT CODE [ aa ] (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for samples following the alarm. (1).When receiving the test requisition information text using online, the text classification code is out of specification. (2).The display of [ ] and its meaning are as follows.
6)ONLINE ILLEGAL SAMPLE No. [ aa: bbbbb ] (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for other samples within the run. (1).When receiving the test requisition information text using online, sample No. of the sample generating the alarm does not meet the specification. (2).The display of [ ] and its meaning are as follows.
7)ONLINE ILLEGAL RACK No. [ aaaaaaa: b: cccccccc ] (1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive is designated as "STOP", the following events occur: 1).Disregard the test requisition information text for the sample generating the alarm. 2).System will not receive text for samples following the sample generating the alarm. 3).
8)ONLINE ILLEGAL SAMPLE KIND No. [ aa ] (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for the other samples within the run. (1).When receiving the test requisition information text using online, sample kind No. of the sample generating the alarm does not meet the specification. (2).The display of [ ] and its meaning are as follows.
11)ONLINE ANALYSIS METHOD MISMATCH [ aa <> bb ] (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for other samples within the run. (1).When receiving the test requisition information text using online, sample type of this text does not match the required sample type. (2).The display of [ ] and its meaning are as follows.
(1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for the other samples within the run. (1).When receiving the test requisition information text using online, sample type of this does not match the required sample. (2).The display of [ ] and its meaning are as follows. aaaaaaa : Transferred sample type and sample No.
13)ONLINE RACK No. MISMATCH [ aaaaaa : bbbb <> cccc ] (1). In the Online Parameter menu, submenu Error Control, if the T.R.I. receive is designated as "STOP", the following events occur: 1).Disregard the test requisition information text for the sample generating the alarm. 2).System will not receive text for samples following the sample generating the alarm. 3).
15)ONLINE ITEM ERROR [ aaaaaaaa ] (1).Disregard the test requisition information text for the sample generating the alarm. (2).Continue to receive the test requisition information text for the other samples within the run. (1).When receiving the test requisition information text using online, the test requisition cannot be stored. (2).The display of [ ] and its meaning are as follows. aaaaaa : Sample type and sample No.
16)ONLINE RERUN ITEM ERROR [ aaaaaaaa ] (1).Disregard the repeat run test requisition information for the sample generating the alarm. (2).Continue to receive the test requisition information text for the other samples within the run. (1).When receiving the test requisition information text for repeat run using online, repeat run test requisition cannot be stored with for the following reasons. 1).
