OBJ_DOKU-15442-003.fm Page 1 Tuesday, April 12, 2011 9:57 AM Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-garden.com F 016 L70 737 (2011.
OBJ_BUCH-920-003.book Page 2 Tuesday, April 12, 2011 10:04 AM 2| 7 8 6 9 5 10 4 3 2 1 11 12 AXT 22 D / 25 D AXT 23 TC / 25 TC A F 016 L70 737 | (12.4.
OBJ_BUCH-920-003.book Page 3 Tuesday, April 12, 2011 10:04 AM |3 C D 7 E 8 11 F 13 360° x5 8 9 G H 6 5 4 10 AXT 22 D / 25 D 14 6 5 4 AXT 23 TC / 25 TC Bosch Power Tools 15 16 15 16 AXT 22 D / 25 D AXT 23 TC / 25 TC F 016 L70 737 | (12.4.
OBJ_BUCH-920-003.book Page 4 Tuesday, April 12, 2011 10:04 AM 4| I J 8 15 10 17 10 K F 016 L70 737 | (12.4.
OBJ_BUCH-920-003.book Page 5 Tuesday, April 12, 2011 10:04 AM English | 5 Safety Notes en Warning: Read these instructions carefully, be familiar with the controls and proper use of the machine. Please keep the instructions safe for later use. Before using for the first time, ask for a practical demonstration. Explanation of symbols on the machine General hazard safety alert. Read instruction manual. Before handling the cutter, switch off and remove the plug from the mains supply.
OBJ_BUCH-920-003.book Page 6 Tuesday, April 12, 2011 10:04 AM 6 | English f Do not attempt to repair the machine unless you are qualified to do so. f Do not allow processed material to build up in the discharge zone; this may prevent proper discharge which can result in kickback of material through the chute assembly. f If the machine becomes clogged, switch off and allow the cutter to stop. Remove the plug from the mains supply before clearing debris.
OBJ_BUCH-920-003.book Page 7 Tuesday, April 12, 2011 10:04 AM English | 7 Technical Data Quiet-shredder Article number AXT 22 D AXT 25 D AXT 23 TC AXT 25 TC 3 600 ... H03 0.. H03 1.. H03 2.. H03 3.. W 2200 2500 2300 2500 W 2000 2300 2100 2300 min-1 40 40 40 40 Power consumption, S 6 (40/60 s)1) Power consumption, S 1 No-load speed Drum Drum Turbine Turbine kg/h 1802) 1902) 2152) 2302) mm 382) 402) 422) 452) l 53 53 53 53 kg 31.3 31.3 30.5 30.
OBJ_BUCH-920-003.book Page 8 Tuesday, April 12, 2011 10:04 AM 8 | English It is recommended for increased electrical safety to use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it. If the supply cord is damaged, it must be replaced by a Bosch Service Centre. When using cable drums, these must be completely unreeled.
OBJ_BUCH-920-003.book Page 9 Tuesday, April 12, 2011 10:04 AM English | 9 Adjustment of the pressure plate 15 is necessary as a result of wear (shredded material, e. g. branches, hangs together as a chain and is not properly cut through).
OBJ_BUCH-920-003.book Page 10 Tuesday, April 12, 2011 10:04 AM 10 | English In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the garden product. Removing the Pressure Plate (see figure J) f Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled. f Always wear protective gloves when using, adjusting or cleaning the garden product.
